Dual WAN with some hosts (VLAN tagged) using only one WAN
Hi, I am about to deploy an ER-PoE to load balance 2 WAN links, and supply 2 LANs. My LAN will come off ethX and is fed to my house with a LiteBeam AC. Ideally, I would like to enable load balancing...
View ArticleProblems when connecting over VPN
Backstory:I have set up VPN following this guide (on a EdgeRouter Pro):https://help.ubnt.com/hc/en-us/articles/204959404-EdgeRouter-Set-up-L2TP-over-IPsec-VPN-serverSetting IP settings like this (same...
View ArticleRe: "show openvpn status server" broken with tap interface
I was able to reproduce this issue and created a bug ticket. Thank you for reporting.
View ArticleRe: WAN failover doesn't start for upstream fail
..ok I have to set up a lab to reproduce the issue and try what you suggested to me. I'll get back to you soon, many thanks.
View ArticleRe: Can't establish Site-to-Site VPN
You are correct, it looks like I grabbed the wrong link, but I did follow the correct video.
View ArticleClik here to view.
Re: Can't establish Site-to-Site VPN
Happens probably something simple that we're not seeing (not an extra space in either of the passphrases)
View ArticleRe: Can't establish Site-to-Site VPN
No, I even tried a super simple pass phrases to see if that would help. I did notice that there are no related firewall or NAT rules even though that option was selected, is that normal?
View ArticleRe: Can't establish Site-to-Site VPN
yeah, the "Auto-firewall" rules are set in iptables, and this is not reflected in the config file. you should be able to see them if you use iptables directly on the CLI. sudo iptables -Lshould cover...
View ArticleAdding New User
Well, after going through the GUI to attempt doing this and failing a multitude of times with "User does not exisit!" (well, no kidding) I finally tried to just add a new user so I could get rid of the...
View ArticleRe: Comcast IPv6 issues when hwnat enabled on ER-X
Also, here is what conntrack shows::~# conntrack -f ipv6 -L udp 17 25 src=fe80::46d9:e7ff:fe93:b92d dst=ff02::1:2 sport=546 dport=547 [UNREPLIED] src=ff02::1:2 dst=fe80::46d9:e7ff:fe93:b92d sport=547...
View ArticleRe: Edgepoint capabilities
It seems to me that you already answered his question. I'll just add that it may be a bad idea to try to send 3Amps over POE, USE THE TERMINALS and a dedicated wire of a proper gauge for the amount of...
View ArticleClik here to view.
Re: Adding New User
Not 100% clear here, since you're in the routing subforum (and it's been a day from [curse you word filter]) -- is this for a switch, or a router? edit - nevermind, i re-read things and it clicked...
View ArticleRe: Adding New User
dpurgert wrote: Not 100% clear here, since you're in the routing subforum (and it's been a day from [curse you word filter]) -- is this for a switch, or a router? Oops, I thought I had switched over...
View ArticleRe: VLAN dns help
you are right , this opendns reply: Hello,Thank you for sending the diagnostic file results.It appears that your DNS requests are not reaching OpenDNS.Can you please run the Extended Test in...
View ArticleEdgerouter X - vlan without a switch config included
I want to setup a vlan on the router X i have my isp providing 192.168.1.1 want to set up vlan on configured the eth 2 as vlan 30 assigned the 10.10.0.1/16 ip set up dhcp but i dont have any ips...
View ArticleRe: Setting up DHCP with option 156 not picking up the correct IP address
Did you ever get this fixed? We are having the exact same issue on firmware 1.9.1
View ArticleIP Address on Edgerouter POE - TBD
Model Edgerouter POEeth0 --> Cable Modemeth1 --> UnifiACPROeth2,3,4 --> Switch0 The system was setup with the wizard. On the dashboard no IP address is displayed for eth2,3,4 its states TBD I...
View ArticleEdgeMax EdgeRouterX
Hello I just purchased a EdgeMax Edgerouter X.I have port forwarding for RDP working but I cannot for the life of me figure out how to only allow access from a Public IP Block 68.188.x.x/28. This is...
View ArticleClik here to view.
Revisiting DHCP Relay Issues
I'm still scratching my head why DHCP Relay doesn't work when applied across multiple physical interfaces. There is a bug with the DHCP Relay implementation that prevents the above scenerio from working.
View ArticleRe: Setting up DHCP with option 156 not picking up the correct IP address
So we figured this out a few minutes after I posted this... You have to enable layer 2 tagging like this:option shoretel "ftpservers=x.x.x.x, country=1, language=1, layer2Tagging=1,...
View Article
