Re: VLAN not working on EdgePro with Dual Wan activated
set interfaces ethernet eth2 vif 20 firewall in modify balance Also, to see your config in "command-like" format instead of tree:show configuration commands
View ArticleRe: InterVLAN Issue
I disabled Hairpin and still nothing. You are right about the LAN_IN because it started a WAN_OUT but realized i had it setup wrong, and never changed it.
View ArticleRe: VLAN not working on EdgePro with Dual Wan activated
THANK YOU! Resolved my problem and I learned something. Much obliged. P.
View ArticleClik here to view.
Re: Comcast IPv6 issues when hwnat enabled on ER-X
Yes, the SIGHUP shows. I'll run this and give you the output shortly. /usr/sbin/dhcp6c -Df -c /var/run/dhcp6c-eth4-pd.conf -p /var/run/dhcp6c-eth4-pd.pid eth4 2> /var/tmp/dhcp6c.log
View ArticleRe: EdgeOS Blacklist script
There is also a long thread on this same topic with several similar options posted in this forum: Emerging Threats Blacklist You can also make the configuration changes via GUI or CLI without needing...
View ArticleRe: EdgeMax 1.9.1 dhcp no domain name..
Apart from showing leases (which is fixed and will be available in the next FW release) what is missing for fully integrated dnsmasq?
View ArticleClik here to view.
IPSEC Nat Traversal Packet Loss
I have multiple remote ER Lites connecting back to the same headend ER using IPSEC/GRE. On the ER Lite side, Eth0 gets its address from the local ISPs dynamically. Some are publically routable...
View ArticleRe: Comcast IPv6 issues when hwnat enabled on ER-X
Here is the log and the capture. It appears that DHCP6C is simply not receiving the advertise. Is there a way to CTY to the SOC to do a capture there?
View ArticleRe: Another VLAN config question (ER PoE & TL-SG1024DE)
All the bases covered are better than some of them covered.Yes, I made all the changes in the appropriate places and applied/saved in the TP-Link UI.I'll give the factory reset a shot when I can...
View ArticleRe: QoS (Shaper) kills my config
So are you saying to replace:set interfaces ethernet eth2 traffic-policy out DownStreamwith:set interfaces switch switch0 traffic-policy out DownStreamI did that and so far it seems to be working.Thank...
View ArticleRe: Edgerouter v1.9.1 OSPFv3 interop issue with Cisco 3750G
Thanks for the suggestions I managed to bring the OSPFv3 adjancency between the Edgerouter and Cisco 3750G up, by placing that link to area 1. The remaining Edgerouters are still in area 0. I also...
View ArticleBlock MAC adress
Hi all,I discovered yesterday with ip scanner a strange and suspeted device connected in my network called "camera network" who has a MAC Adress "aa:bb:cc:dd:ff:dd". All my known devices are listed in...
View ArticleRe: ER-X 1 WAN and 3 Separate LAN
Yes you can--it's the same approach as for twoLANs. First of course, you need to eliminate theswitch and use separate ports instead. Assigna separate LAN subnet to each port, and createseparate DHCP...
View ArticleRe: Block MAC adress
rafie wrote:Is adding a new rule by source (MAC Adress) in the firewall rules, enough?ThanksYes, that should be enough, did you try it to see if it worked for you? Still, you should hunt down that...
View ArticleL2TP VPN setup
Could someone walk me through the correct setup for this: I have 3 networks coming together: 1) DHCP internet access, 2) internal network, 3) vLan from the corporate network. (does not have internet...
View ArticleRe: IPSEC Nat Traversal Packet Loss
Post your config. Did you set up the NAT networks under nat-network allowed-networks on ER-L A+B?
View ArticleRe: Block MAC adress
i didn't seen it back again today, so i'm waiting for a new connexion from, before attempting a hunt down, if i can fiind out phisycally or block it to see if the firewall rule works
View ArticleRe: Load Balance, QoS, Voip and Sticky Connections
Were you able to get this working? I have nearly the exact same issue. I have the load balancing working, but no QoS is being applied to the VOIP and it breaks up constantly...
View ArticleClik here to view.
Re: InterVLAN Issue
It was an error on my part, forgot to set a default gateway on the windows dhcp server.... If I could have tested with a laptop I would have figured it out, but I was using a yealink phone and never...
View Article
