Re: Comcast IPv6 issues when hwnat enabled on ER-X
IPv6 has been lost after a couple hours. Release/Renew does not bring it back. Release, delete duid, renew also does not bring it back.
View ArticleInternet Blacklist or blocking Javascript
I'm trying to configure a new EdgeRouter Xv1.9.1 to try to block all websites but 10 in an attempt to have PCs online that can't get sick from drive-by malware and such. I'm pretty sure I don't really...
View ArticleRe: Chronic connection timeouts on 1.9.1
Hi i was trying to use diff between configurations with little luck. There are some changes in between and I am not sure which is the last 'good' config and the first 'bad' one. I was trying to do it...
View ArticleRe: Edgemax with Google Fiber and TV
- You are using 192.168.1.1/24 for your LAN on eth2. That should be 192.168.1.0/24 . I'm also not convinced it's the best choice for the LAN as the Google Network+ box also uses that same subnet by...
View ArticleRe: Edgerouter v1.9.1 OSPFv3 interop issue with Cisco 3750G
I see from frame 18 of the capture that the Cisco sent a couple of LSA that Wireshark doesn't recognise. It seems they're Intra-Area-TE-LSA type (0xa00a) from Traffic Engineering Extensions to OSPF...
View ArticlePPTP Strange error..
I am having the strangest error.... I've a simple PPTP server set up, with local authentication, but the clients will never connect.. firewall { all-ping enable broadcast-ping disable group {...
View ArticleRe: Chronic connection timeouts on 1.9.1
I wish I could. I went back to 1.9.0 as fast as I could since 1.9.1 was performing so poorly. I'm not sure if I'll be able to experiment with it much since I'm relying on this router for my home...
View ArticleERlite3 - Setup router/firewall (only) mode for public /24 net? no NAT wanted
Hello, I've got a dorm with ~ 150 students. The university is the internet provider and put a (I believe it is a router) device in. Fibre goes in, ethernet comes out. So far, DHCP was enabled and...
View ArticleRe: log tail problem with log rotate
That would indeed be the purpose of syslog, and is exactly the use case for using remote logging via syslog. For many log files in /var/log the application does not write directly to the file - it...
View ArticleRe: How to detect when default route to internet is not reachable and...
tnx for your response, could you give an example of the script? i've never do this before tnx for your time
View ArticleOpenVPN through ssh - local DNS resolution via dnsmasq not working
Hi there, I set up an own private network with the ER-X in a computer lab in my university. Due to firewall restrictions I'm only able to use ssh to connect to an internal server. So I though I could...
View ArticleRe: ERLite 100% CPU usage - All HW offload enabled
16again wrote:Note most of the packets in previous pcap were unicast and had a vlan=2 tag, so be prepared to mis packets when inserting a switch and hook up sniffer on itWill I miss the packets if the...
View ArticleInterVLAN Issue
I've been reading the forums for intervlan but I am just not sure why it isn't working properly. I am able to ping the vlan gateway but no the clients on the vlan. I played with firewall rules but I...
View ArticleRe: VLAN not working on EdgePro with Dual Wan activated
I see the difference between the two below: speed auto}ethernet eth2 {address 192.168.50.1/24description Localduplex autofirewall {in {modify balance}}speed autovif 20 {address...
View ArticleEdgeOS Blacklist script
Hi all, I'd like to contribute a script I've been using on my ERX Supports IPv4 and IPv6 blacklists - including mixed listsWorks with most sites and easy to add them - tested with SpamHaus, OpenBL,...
View ArticleVlan Aware on Switch0 unavailable now on V1.9.1
So I am trying to do inter vlan routing in a ERPOE-5 and the vlan tab on the config is missing so I go the tree and under switchport I enable vlan aware and it says:Error: platform does not support...
View ArticleRe: ERLite 100% CPU usage - All HW offload enabled
Unicast might also be a problem. Best way to go: Use manageable vlan capable switch , create proper VLAN/port settings, and configure a so called monitor port. (it is a port that sends out copy of...
View ArticleRe: ERLite 100% CPU usage - All HW offload enabled
16again wrote:Unicast might also be a problem. Best way to go: Use manageable vlan capable switch , create proper VLAN/port settings, and configure a so called monitor port. (it is a port that sends...
View ArticleRe: InterVLAN Issue
Try to disable Hairpin. For purists: Better rename your firewall ruleset called WAN_OUT into LAN_IN, as it is applied on LAN in ingoing direction.
View Article
More Pages to Explore .....