Re: Working with pseudo ethernet and 1to1 NATing to servers
Can you post a few screenshots of the peth + snat rules?Following a guide really helps pin down the needed config to run with dual IP's.Thanks!
View ArticleRe: Owner changed on scripts during FW upgrade from 1.8.0 to 1.9.1
I was hoping someone from the development side would chime in with some details regarding how the UIDs are handled during a FW upgrade. Should I just chown the scripts and move on?
View ArticleRemote User VPN can't access site-to-site VPNs
Hi, Site A - Office - 192.168.16.0/24Site B - Servers - 192.168.15.0/24 Site A and B are connected using a site-to-site VPN. From A, you can ping any server in B and vice-versa. Then I have a...
View ArticleRe: Remote User VPN can't access site-to-site VPNs
Post both configs and routing table of site a.
View ArticleRe: Firewalling OpenVPN Site-to-Site
Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 8940K 1132M UBNT_VPN_IPSEC_FW_HOOK all -- * * 0.0.0.0/0 0.0.0.0/0 8940K 1132M VYATTA_FW_LOCAL_HOOK...
View Articleclassic routing versus NAT routing
I have an ER 8 and I want to use classic routing. I will take an address on a /30 for my WAN address from the cable company. They will give me a CIDR on a /29 that routes to the /30 to hand out to...
View ArticleRe: Firewalling OpenVPN Site-to-Site
Well there are packets going thru VTUN1_LOCAL, 6 accepted as est/rel and 1202 logged and dropped by default. But 0 packets for VTUN1_IN. Both chains are defined and hooked in appropriately it would...
View ArticleEdge Router Lite as Standalone VPN Server
Is it possible to use ERL purely as a VPN server with only one port connectted? I have an asus AC68 as my main router and the ERL eth will be plugged to asus LAN port. Thanks in advance.
View ArticleRe: Edge Router Lite as Standalone VPN Server
yes, there's no reason that can't be made to work. Why not just replace the asus altogether?
View ArticleRe: classic routing versus NAT routing
yes, this is totally possible. You may even be able to use UCRM to do all the hard work for you.
View ArticleRe: EdgeRouter X - WAN + CoreSwitch (Switch0) + Distribution Switches
Hi Guys, Guess what? Everything's working as I wanted now I'll start building the firewall rules to restrict the access between vlans since they are all routed and communicating. I recently changed ISP...
View ArticleRe: Requests/suggestions for new hardware models
broken wrote:10Gbit ER is necessary when XG10 EdgeSwitch is already on the market. I hope they will developing it on Cavium Octeon platform which works excellent on current ER-Pro. Maybe Octeon III ?...
View ArticleWLB Sticky Session TIme
I am not sure if this has been discussed or not. I was unable to find it in the forums. But is there a way to see what the sticky session time is and to even extend that time?
View ArticleRe: local file access over l2tp vpn connection
You shoud be able to connect to the server. However, you will not see the server in the Windows network browser like you would if the server was on your LAN. Did you try directly accessing the server...
View ArticleRe: Firewalling OpenVPN Site-to-Site
I made some progress. I thought it might have something to do with the fact that the local and remote addresses are inside the static routes. Currently: ERL-A has local-address set as 192.168.5.1 and...
View ArticleERL + CenturyLink 1gig. Stuck at 100meg
I have been using my EdgeRouter Lite with CenturyLink's 100meg fiber service for a little over a year now. Recently I decided to upgrade to 1gig thinking that it would be a fairly simple upgrade. Alas,...
View ArticleOptimum setup for EdgeRouter PoE
I recently purchased 3 UniFi AP AC Pro WAPs and an EdgeRouter POE for a home residence, in conjuction with an existing unmanaged Cisco 24 port switch (SG102-24-NA). My goal is a fast, stable, simple...
View ArticleRe: ERL + CenturyLink 1gig. Stuck at 100meg
You confirm the LAN port(s) are at Gig as well? It maybe something with the bridging of the interfaces (I remember seeing a post here about it causing performance issues, but I don't know if that would...
View ArticleRe: function to change configuration
randydrobinson wrote:This is my code: #!/bin/vbash function changeUbntConfig() { configure set interfaces ethernet eth0 description changed_by_script commit save exit } # tests...
View ArticleRe: ERL + CenturyLink 1gig. Stuck at 100meg
That is correct bridging is software based and utilizes the CPU, and as such has a limitation usually under 100Mbps. Remove the bridge and your problem will be solved.
View Article
More Pages to Explore .....