Re: Very strange ER pro8 behaviour on facebook, instagram and some sites
goldlineIT wrote:Are you getting RFC1918 (private address's) from your cellular routers? and what he's asking is if you unplug 2 of your wans does everything work ok off the 1 WAN? He wasn't asking...
View ArticleRe: Losing connection to server using remote desktop
Here I was able to extract itfirewall { all-ping enable broadcast-ping disable ipv6-receive-redirects disable ipv6-src-route disable ip-src-route disable log-martians enable name WAN_IN {...
View ArticleRe: Edge Pro - multiple wan ip not working
You have a disparity between the NAT rules. description "Fred Static" destination { address xxx.xxx.xxx.179 }inbound-interface peth11 inside-address { address 172.30.204.2 } log disable protocol all...
View ArticleRe: Can ER-8 config be loaded onto ERPro-8
Should work perfectly fine. Best bet would be to give the ER-Pro a base config (even the basic wizard will suffice) before loading the backup. Sometimes things get a little weird when there isn't a...
View ArticleRe: DPI: Netflix not being flagged
There's two ways (that I know of) to identify a SSL stream. You can look at the IP address, but that won't work with Open Connect because the IP address isn't registered to Netflix. Or you can look the...
View ArticleRe: How To Use RSA Key or Certificate with VPN Instead of Pre-Shared Key?
Instructions........like these ?
View ArticleRe: LAN to LAN and WAN failover in both LANs
Make wireless link is an L3 link between edgerouters (on it's own subnet) Basically, both ERs run their own loadbalance instance , using the wireless link as...
View ArticleEdgeRouter upnp2 limit?
I have an EdgeRouter ERLite-3, using upnp2 for Back to My Mac. Every so often I can't get to a system remotely, and it appears that the Mac thinks that the router is not set up properly (I get a...
View ArticleRe: How do I back up or load config in CLI from a Mac?
First, set up ssh keys (ssh-keygen) so that you can ssh to your ER from Mac without user/password. Then you can: scp ERHostName://config/config.boot . and scp config.boot...
View ArticleRe: l2tp works from LAN but not from WAN
Here are the requested logs: Syslog: Feb 1 16:54:15 sagitta kernel: [NATCOM-LOCAL-50-A]IN=pppoe0 OUT= MAC= src=200.113.234.211 DST=190.102.87.30 LEN=284 TOS=0x00 PREC=0x00 TTL=48 ID=0 DF PROTO=UDP...
View ArticleRe: Allow ports through firewall and NAT - ER-X
I figured out that the MyQ device is assigned 192.168.0.100. I added a static mapping for that MAC address to that IP address. I assume that this means that whenever the device connects to the router,...
View ArticleRe: Allow ports through firewall and NAT - ER-X
use port forwarding OR DNAT & firewall, but not both (they "essentially" do the same thing, and running both in parallel tend to cause issues -- or at least it used to). Out of curiosity, your ER...
View ArticleRe: Requests/suggestions for new hardware models
I'd like an all 10Gbase-T (non-SFP+) version of the US-16-XG and ES-16-XG.
View ArticleRe: Edge Router X with lots of users
As mentioned, ER-X or USG will handle this just fine. That said, looks like most of your users will be just cell phones and maybe some laptops to access internet. Also it looks like you'll need more...
View ArticleRe: Requests/suggestions for new hardware models
TheRedBaron wrote:I'd like an all 10Gbase-T (non-SFP+) version of the US-16-XG and ES-16-XG.That makes no sense... SFPs are way more flexible. A better option would be for UBNT to sell a 10GbaseT SFP+...
View ArticleRe: Using traffic priority QoS
If the inbound rule can be setup to use a destination that would be select after NAT processing that would make it easier to target specific IP addresses/devices instead of just destination ports or...
View ArticleRe: IPV6-PD on Edgerouter X
Hi thanks again for helping! Not sure if this means anything but when i renewed the address on my iphone i saw the ipv6 dns name servers from my router-advert directive eg (2001:8000:101::1 and...
View ArticleRe: Allow ports through firewall and NAT - ER-X
I followed the script in the previous link on port forwarding, which did both PF and DNAT/FW rules. I will delete the firewall and DNAT rules. It had no effect - still no connection. When I go to the...
View ArticleRe: Allow ports through firewall and NAT - ER-X
Post your current config so we can take a look.
View Article
More Pages to Explore .....