Re: VoIP issues - only one phone is able to make outbound calls.
Absolute nothing I've tried is working, removing phones from the dept moves the phone able to make outbound phones too. For instance in the old setup 1.1.13 was able to make outbound phones, if I...
View ArticleRe: Replacing At&t U-verse gateway with Edgerouter
https://community.ubnt.com/t5/EdgeMAX/Ultra-Newbie-with-ER-X-amp-Uverse/m-p/1732621#M136244
View ArticleRe: 1.9 dnsmasq for DHCP
How'd you do the rule for this ?I'm experiecing the same with dnsmasq, had people over and noticed that dhcp wasn't working for the guest wireless network (on a different vlan). Disabled dnsmasq and...
View ArticleRe: Replacing At&t U-verse gateway with Edgerouter
What I have done is Spoof the MAC adress of the ATT gateway on to the edgerouter port where you connect the ONT device to. I have a couple locations set up this way. Keep the ATT gateway near by...
View ArticleRe: Private Internet Access Open VPN - Step by Step Configuration
Just switched to Seatlle which would be my closest server available and pulled 18.15 Mbps download and 19.50 Mbps upload. I am stoked with this my total is 100/20 from my ISP. Pings really good at 18...
View ArticleRe: Setting Up VPN service connection and Wireless Network
Just wanted to update that I got this set up and running starting with the links you provided. It was a good start. Thanks again!
View ArticleRe: Traffic Analysis - UCTalk
from my research it seems that the DPI recognized L2TP traffic as: UcTalkAnd this is a false possitive.I don't know if this is your case but it's possible.You will just need to inspect this specific...
View ArticleRe: IPV6-PD on Edgerouter X
yes my isp Telstra allocate a /56 prefix for the network via PD but it doesnt provide an address to the router itself hence why i didnt configure the host-address option
View ArticleRe: IPV6-PD on Edgerouter X
Well slaac automatically configures router advert you should really simplify to something like this only and troubleshoot from there, After getting it working then you can call use your own RA...
View ArticleRe: IPV6-PD on Edgerouter X
Also after doing that many changes you might want to do a reboot and delete your duid
View ArticleRe: IPV6-PD on Edgerouter X
Okay giving it the simple configuration like that i get cat /var/log/messages Jan 31 13:09:59 ubnt radvd[3907]: no auto-selected prefix on interface switch0, disabling advertisements Jan 31 13:10:00...
View ArticleRe: IPV6-PD on Edgerouter X
Are you sure your modem is ipv6 compatible? are you residential or business?
View ArticleRe: IPV6-PD on Edgerouter X
https://crowdsupport.telstra.com.au/t5/National-Broadband-Network-NBN/IPv6-over-NBN-broken/td-p/633783Here's more proof your ISP might not be giving you ipv6
View ArticleRe: Edgerouter PoE 5 - GUI no - console yes
IP forwarding is on I've tried assigning IP addresses on pretty much all the ports - doesn't make a difference.
View ArticleSetting DHCP Code 150 issues
ERL updated to v1.9.1, trying to configure DHCP option Code 150 for VOIP service. I have been scouring the internet and trying all possible combinations but nothing seems to work. Typical entry: set...
View ArticleRe: Setting DHCP Code 150 issues
Try: set service dhcp-server global-parameters "option tftp-server code 150 = ip-address;" set service dhcp-server shared-network-name VoIP subnet 192.168.0.0/24 "option tftp-server 192.168.0.253;"
View ArticleClik here to view.
Re: IPV6-PD on Edgerouter X
Okay so i have tested with the original modem router acting as the gateway and modem and achieved these results, that is to say i get an ipv6 address.further as stated previously there isnt an ip...
View ArticleRe: Setting DHCP Code 150 issues
Just confirming you're typing "configure" before issuing commands correct?
View Article