Re: UPnP Remote Play
so then how do you enter configuration mode? typing config doesn't seem to work. or configuration. Also my internet is port 0, and my ps4 is plugged into eth3. Upnp wizard doesn't seem to be working as...
View ArticleRe: VRRP - Not sending advertisements at configured intervals, breaking VRRP
Yours are spaced at (multiple of ) 1 second intervals, and not at random intervals , like 3.1415 secondsThis suggests some advertisements are getting lost. re-run tcpdump, so that we can see id # too,...
View ArticleRe: EDGEROUTER can't obtain IP from WAN after hours
Normally I'd suggest: check WAN_LOCAL rules to see if DHCP traffic is allowed. If it repeats like clockwork at 7:00 AM , it might be provider issue, which might be checked by:add a switch between...
View ArticleRe: firewall vlan
Direction should be IN. You say if you use IN, you cannot start NEW connections to VLAN but that is what you state you want above where you state you want to block VLAN2 to VLAN. rule 2 should be drop...
View ArticleRe: ER-8-pro Public ip's on lan side handed out with dhcp server ....anyone a...
Your going to need a firewall rule excluding those ip's as well on WAN_IN
View ArticleRe: VoIP - Drop calls after 30 seconds
I have an idea, please provide some more information. ;-)Is it a wireless phone? What kind of ISP do you have. What VOIP service is it. What is your bandwidth. Post your config.
View ArticleRe: Comcast IPv6 Settings Questions
goldlineIT wrote:@smf22DAD traverses the router? That sounds more like a multicast process. You stated it was above...I guess I didn't read all the way down. So my original question remain. Just to...
View ArticleRe: Private Internet Access Open VPN - Step by Step Configuration
No problem. Glad you got it working. Wasn't so bad huh? That would be frustrating for sure. No rebooting issues on my standard USG. Let me know what kind of throughput you get on speed tests. Mine is...
View ArticleRe: VoIP - Drop calls after 30 seconds
Who do you have for ISP? and how about answering the other questions asked as well....
View ArticleRe: UDP packet loss with EdgeRouter Lite
ooferomen wrote:if you are using iperf3 you need to set the packet size with -l to something like 1470. that will take care of the huge packetloss but you will still see some out of order packetsDidn’t...
View ArticleRe: Private Internet Access Open VPN - Step by Step Configuration
Im sure Ill get better performance hooking to the seattle or west servers. Through the netherlands I just pushed 6.06 Mbps down and 8.50 Mbps up What tweaks have you been making for your performance...
View ArticleRe: Private Internet Access Open VPN - Step by Step Configuration
Well I am not really 100% sure what the changes mean haha. But doing some research and testing different suggestions I found online. I ended up adding these lines to my .ovpn config file. fast-iomssfix...
View ArticleRe: ER-X-SFP PoE input
No: if you want to permit flow, use a piece of wire. A diodeis used to restrict flow to one direction--against [anti] theother direction. Dave
View ArticleRe: Private Internet Access Open VPN - Step by Step Configuration
OK cool I will do some of my own testing with this throughout the week. if I want to remove my host ip from the OPENVPN group and put a new host or subnet, do you know how I go about removing...
View ArticleRe: USB Modem support
Any progress on including the USB serial modules for ER models that have USB ports? It's baiscally the only thing preventing me from getting a sane failover to LTE setup with a ZTE MF831 on my ERPro-8.
View ArticleRe: IPv6 Over OpenVPN Tunnel?
Interesting idea! It does work - or at least, it assigns a /64 to the vtun0 interface. But I still don't know how to tell OpenVPN to route via that /64. I suppose I could just manually specify that...
View ArticleRe: Private Internet Access Open VPN - Step by Step Configuration
The line you are using to add. set firewall group address-group OPENVPN_COMPUTERS address 192.168.11.13if you change set to delete. it should delete the IP. or subnet if you have them aded by subnet.
View ArticleRe: IPv6 Over OpenVPN Tunnel?
Unfortunately I know nothing about openvpn, But i've seen other people suggest adding "route-nopull" or something like that to the client side to keep the routes from being added to the server. maybe...
View ArticleRe: IPv6 Over OpenVPN Tunnel?
Does this help you at all?https://community.openvpn.net/openvpn/wiki/IPv6
View Article
More Pages to Explore .....