Re: ERPoe-5 routing and internet "passthrough"
Your config won't help me though. As long as the switch on the ERPoe-5 doesn't actually support vlans (it supports virtual interfaces, but tagged/untagged/trunk isn't possible), I have to find some...
View ArticleRe: TOP SITES ADULT
You can use this command:$ /usr/sbin/ubnt-dpi-util show-cat-apps [category]
View ArticleRe: ERPoe-5 routing and internet "passthrough"
The ERPoE is a router, so use it as a router since you already have another switch. Pull all of the interfaces out of the 'switch' configuration so that each port is it's own routing port, and I think...
View ArticleRe: ERPoe-5 routing and internet "passthrough"
The ERPoe-5 is a router with three switched ports. The manual states that the switch ports are VLAN aware. I checked this before I bought it. The switch that the ERPoe-5 is connected to is a dumb...
View ArticleCan't Connect to Edgerouter PoE interface after Setup
I'm hoping someone can help. I have an edgeroute PoE that is overkill for what I needed. I purchased it a couple months ago and set it up with 2 unifi AP's connected to eth3 and eth4, and I have my...
View ArticleRe: ERPoe-5 routing and internet "passthrough"
I have installed the ERPoE for customers before. You can remove the ports from the switch interface. Attached is a screenshot of what it looks like in the GUI. Just uncheck the boxes, and those...
View ArticleRe: ERPoe-5 routing and internet "passthrough"
What you may want to look into is adding a bridge interface and then adding the vlan interface you want to the bridge, then adding those three ports to the bridge interface, this would allow you to...
View ArticleRe: ERPoe-5 routing and internet "passthrough"
Decoupling the ports from the switch won't help me. Those three ports share one link, maxing out at 1gbps. I need traffic to stay within the switch and out of software as long as the traffic is going...
View ArticleRe: EdgeRouter X: Cannot use port forwarding from internal network
Hmm, I have hairpin NAT enabled on the port forwarding page, but it doesn't seem to be working.
View ArticleRe: List of Compatible USB drives
lg wrote:THE SANDISK CRUZER FIT NO LONGER RELIABLY WORKS I just tried the following having just received them from Amazon and they DID NOT work: SanDisk Cruzer Fit 8GB, BI151125185DSanDisk Cruzer Fit...
View ArticleRe: ERPoe-5 routing and internet "passthrough"
I got the ERPoe-5 over the Edgerouter-X because the X would be too slow, and so that I could add one or two AP AC Pros without needing injectors.If the switch ports were actually VLAN aware as it says...
View ArticleRe: Firewall question with bridged ethernet ports
The ER-POE has L2 capability for eth2, eth3, eth4. You wouldn't want to bridge these and instead would want to create a switch with these. You only listed three devices, but if you truly need four...
View ArticleRe: ERPoe-5 routing and internet "passthrough"
repvik wrote:The ERPoe-5 is a router with three switched ports. The manual states that the switch ports are VLAN aware. I checked this before I bought it. The ER-POE dow not have "VLAN Aware"...
View ArticleRe: List of Compatible USB drives
My point was that the company which made the d a m n thing should know the timing tolerances required for USB storage devices to work because they had to know that when they ordered them from the...
View ArticleClik here to view.
Re: ipsec vpn newbie help
Thank you, I looked at the response a week ago and was to concerned in not setting up a VPN before it took some time to understand what you said. I one night I had.. an awakening and immediately felt...
View ArticleWorking with pseudo-ethernet on WAN
I'd like to conduct an experiment in working with virtual interfaces and tweaking the NAT rules so that I can separate my home internet traffic from my web server for better security logs. When adding...
View ArticleRe: ERPoE-5 Setup/Configuration Question w/ UAP-AC-PRO
Hi guys! complete newbie here, I intend to set up a home network with 3 UAP AC LRs. Total connections required is 9 (3 desktop, 2 Android Boxes, 1 CCTV & 3 UAP AC LRs) I was hoping to have a...
View ArticleClik here to view.
Re: dealing with ridiculously low bandwidth and VOIP
I think I figured out why the traffic shaping does not work: tcpdump -vvv -i eth0 'udp and not src net 192.168.0.0/16 and port not 22 and port not 53'shows me RTP packets coming in from the SIP...
View ArticleClik here to view.
Re: ipsec vpn newbie help
joel1 wrote:Thank you, I looked at the response a week ago and was to concerned in not setting up a VPN before it took some time to understand what you said. I one night I had.. an awakening and...
View Article