Re: VPN - no peer config found
I thought I would share the solution on this. Thanks to the contributors for their assistance. The issue was being caused by the remote end. Fortigate appliance at the other end, the controller of...
View ArticleSharing a WAN port - no load balancing or failover
What I would like to do is basically bridge 2 eth ports together or set up in a VLAN to act as the WAN side of the router. I do not want to set up a 2nd Internet connection to do any failover or load...
View ArticleRe: Sharing a WAN port - no load balancing or failover
You don't want to bridge, but you do want to switch.You can buyER-XorER-X-SFPorER-12they all have switch chips in them. Good luck!
View ArticleWhy did it just stop working?
Bought this router a couple months ago and it's been working fine. I haven't done anything with it but let it sit there and do it's thing since the first set up. Today I turned my computer on and...
View ArticleRe: bgp race condition at boot in 1.9.1.1 and 1.9.7+hotfix1
Install bird instead of internal Routing Daemon. If you wait for UBNT to fix that issue, you have to wait forever....
View ArticleRe: ERX-SFP UPS
FYI if you look at the small wall-wart that comes with the ER-X (not the SFP) it is a 12V unit. So yes the ER-X SFP will also work on 12V, or rather 13.8 which is what a "12V" battery actually floats...
View ArticleERLite‑3 - Overloading
I am having this weird issue where my brand new ERLite‑3 is getting overloaded, resulting in loss of internett for a short time. From time to time I lose internet, and my PRTG server reports overload...
View ArticleRe: ERLite‑3 - Overloading
The config: firewall { all-ping enable broadcast-ping disable group { } ipv6-receive-redirects disable ipv6-src-route disable ip-src-route disable log-martians enable name VLAN2_IN { default-action...
View ArticleRe: ER-Lite to ER-4 Migration
I transferred and edited my config from an ER-8-XG Infinity to an ER-6P and it worked well. Relabeling and activating the appropriate interfaces will be important, but will be much easier for you since...
View ArticleRe: ERLite‑3 - Overloading
That's kind of what happens when you disable hardware offload by bridging ports
View ArticleProblems with default-originate and IPv6 (BGP)
Hello, I'm trying to announce a IPv6 default route via iBGP to a neighbor, but it's just not working - the default route is not advertised.The same setup seems to work fine for IPv4. Here are the...
View ArticleConnect AP-AC Lite to ER-X Router
Can I connect and power the Ubiquiti Unifi Ap-AC Lite with the UBIQUITI ER-X Router, Black eth4/POE out port? Thanks
View ArticleRe: Second OpenVPN Instance Help
Any ideas from anyone else? I'm beginning to think it might be the fact that on this platform openvpn/openssl runs as single processes and the differing encryption methods for the site to site and...
View ArticleRe: ERLite‑3 - Overloading
Does /var/log/messages contain any clues at specific times ?Do you monitor bandwidth too?
View ArticleRe: ERLite‑3 - Overloading
wrote:That's kind of what happens when you disable hardware offload by bridging ports But that is needed if not the troughput is very slow... Maybe wrong router to use then?
View ArticleRe: ERLite‑3 - Overloading
wrote:Does /var/log/messages contain any clues at specific times ?Do you monitor bandwidth too? Yeah I had this one. As the WAN in has 2 VLANs, it seems IPTV is spiking. But PRTG does not report...
View ArticleRe: Second OpenVPN Instance Help
I see some things that I don't understand, eg, on the vtun0, <local-address 10.99.99.1><local-address 10.255.12.1>, <remote-host 192.0.2.1><remote-host 208.50.x.x> , on vtun1,...
View ArticleRe: Connect AP-AC Lite to ER-X Router
You'll need to use PoE to power the ERX, and in that scenario: Yes. UAP-AC-Lite Power Injector --> ERX Port 0 --> ERX Port 4 in passthrough mode --> UAP-AC-Lite
View ArticleRe: Second OpenVPN Instance Help
Can you post the latest OpenVPN configuration on the EdgeRouter and the client config file? Ben
View ArticleRe: Can't access IotNet from HomeNet
Looking at the output, the 192.168.4.220 client is not respondig to the ping requests. Can you post the latest EdgeRouter configuration? I recommend testing your firewall setup using two PCs with their...
View Article