Re: forbid port use by router
Not using it, but trying to block users from exposing their AMT. The WAN_Local was a test. I have the same rules on the out ports. Most probable if they are opening those ports, it would be by some...
View ArticleRe: forbid port use by router
You would block this on a LAN IN firewall. Not sure I agree with your logic, but its there for you to block if you want.
View ArticleRe: forbid port use by router
Does AMT setup connections to the internet (which I doubt), or are you trying to block new connections from the internet to your AMT ? The latter requires NAT configuration to be present on the ER, as...
View ArticleRe: forbid port use by router
Nobody can expose any port to Internet without you opening the port on WAN_in. Do others have admin access to your router?
View ArticleRe: Pixelserv Debian Package for ER and ER-X Series Routers v1.0.4
, first, how are you blacklisting the adverts?
View ArticleRe: New setup with Pihole not working
Yeah the forwarding loop was the main issue and I wasn't able to figure my out around that one. When I had the pihole setup with DDWRT I was able followed instruction set 2 shown at...
View ArticleRe: Send WOL packet from Server to EdgeRouter
Okay. ethtool eth2 reports no data available despite my switch plugged into it, so since switch0 interfaces with eth2-4, I checked switch0 using ethtool and it does not say something about WOL, so I...
View ArticleRe: forbid port use by router
I'm trying to block new connections from the lan side's amt ports to the internet, which shouldn't need any special setup on the router. This should happen if malware called their command ip reporting...
View ArticleRe: Recommendation(s) on symmetric gigabit WAN setup using EdgeRouter model(s)
Thank you all for all the feedbacks. I'm told once again that the WAN i have is symmetrical at the point of entry to home, i.e. 1 GbE up and 1 GbE down. So, on that, i will continue my investigation on...
View ArticleRe: New setup with Pihole not working
I’m confused. The PiHole is 192.168.1.2, correct? You are advertising 192.168.1.2 to your DHCP clients so therefore they should be querying the PiHole directly and you should see requests per-host.The...
View ArticleRe: Recommendation(s) on symmetric gigabit WAN setup using EdgeRouter model(s)
For 1G/35M I'd go with ER-X/ER-X-SFP ...it'll give you about 900 down which in reality you will not be able to saturate anyway on home connection.Or get ER-4 if you really want to get the best available.
View ArticleCreating Custom Category Of Sites To Block
I am attemtping to use the CLI to create my own category called CustomSites and add multiple sites to block. This is the commands I issued, but I get an error of Unknown application...
View ArticleRe: New setup with Pihole not working
Yowza! I've been making this way harder on myself. You're the best! Thanks for talking me through this
View ArticleRe: RFE: reject route for full Prefix Delegation assignment
Thanks. The filter has the same problem. It doesn't automatically track any updated Prefix Delegation assignmant. What I have now is this in /etc/rc.local: # Finally reject the unmapped part of our...
View ArticleRe: Serial connection to UBNT
Just a picture from the website where I bought it. Mine is set to 3.3VIn case it burned it the leds wouldn't light I think. On my router LEDs are still working in case I power on or connect and...
View ArticleRe: Recommendation(s) on symmetric gigabit WAN setup using EdgeRouter model(s)
wrote:And just for completeness... the ES-8-150W and the US-8-150W (but not the US-8 or US-8-60W) are both 10-port switches, in spite of their names. They have 8 copper GigE ports, and two SFP ports....
View ArticleRe: Serial connection to UBNT
wrote:Is that okay that 3v3pin is giving 0.0 voltage ?Nope, not OK. You've most likely burned the serial port on ER-X. As it seems this did not affect the router, but you are without serial port.
View ArticleRe: Emerging Threats Blacklist
It seems that there is a latest version 1.0.4 for iprange but is not capable of being installed due to outdated dpkg version. For ER-x , the system architecture is mipsel, while fo the rest it is as...
View ArticleRe: Setting up EdgeRouter 4, EdgeSwitch 16, and UniFi AP Pro -- Overkill?
I never knew guest networks were common, so I suppose if you do that, it might make sense.
View ArticleRe: Is it possible to use Edge Router PoE 5 port as a normal PoE switch?
Any idea if the ERPoE will be able to power the Netonix WS-Mini-6 with a 48V PSU? I’d managed to power my UAP-AC-SHD via my ERPoE ever since I got it a more powerful power brick (& made the 48v...
View Article