Re: Schedule for powering the PoE interface on EdgeRouter X?
I have read it and I've seen that feature in UniFi Controller software the first day I got the AP, but I'm looking for a way to do it from the router by disabling the power to an AP.
View ArticleEDgeRouter X v1.9 hangs every couple days
Anyone else having issues with the EdgeRouter X (firmware v1.9.0) hanging up every few days? I restart it, and it will run fine for several days, then internet connections will start to get slow, then...
View ArticleRe: Auto Provisioning
I'm curious if anyone made any headway with ansible. That was an interesting link I've scratched up some commandline bits to help deploy common settings, but would like something more formalized and...
View ArticleRe: EDgeRouter X v1.9 hangs every couple days
No: I use ER-X / 1.9 on my office network, and itruns literally 'forever' without reset. I have hadsome issues over the years with my MotorolaCATV modem and the ISP circuit, where itcan benefit from a...
View ArticleRe: Prevent/restrict access to the router from subnet.
What would you suggest for VLAN_IN and VLAN_LOCAL, considerings that I have more than one VLAN, don't want any of guest devices (except the ones that are reserved) to access the router?
View ArticleRe: Printers not showing under DHCP leases.
That's a fine answer. Why do you care if the printers 'show up' in the DHCPlease list? If they're working, they obviously have asuitable LAN connection. Dave
View ArticleRe: EDgeRouter X v1.9 hangs every couple days
Yeah, that's what I would expect it to do, but it seems pretty unstable here. For a while, I had traffic analysis turned on, and I noticed it would be using most (e.g. 80%) of the CPU and RAM, so I've...
View ArticleRe: Schedule for powering the PoE interface on EdgeRouter X?
As others have explained, there is no built-in methodto turn off a PoE port on schedule. I suppose you couldhack something using a cron job, as was suggested. This controller feature was designed to...
View ArticleRe: EDgeRouter X v1.9 hangs every couple days
I suppose with any complex device there could be anunusual set of settings or use patterns that mightyield an issue. But I can't guess where that would be. If you can spot something in the log that...
View ArticleRe: Design Review / Sanity Check - Robust home network - ~$1,000 budget
Most devices are shipped with obsolete firmware;Ubiquiti often makes updates. Be sure to updatefirmware on the router before first use--there hasbeen a huge improvement. After you update the firmware,...
View ArticleRe: EDgeRouter X v1.9 hangs every couple days
Good idea. I'll reinstall the firmware tomorrow, and see how it goes.
View ArticleRe: Design Review / Sanity Check - Robust home network - ~$1,000 budget
IDF = Intermediate Distribution Frame, which could be just a switch to act a as repeater between cable runs over 100 meters. Needing more than 100 meters (328 feet) in a single run is rare inside even...
View ArticleCan anyone explain why this is happening? 100% CPU usage, maxed out WAN...
Just bought the router a few weeks ago and everything went well. The last few days, I get this: https://i.imgur.com/XwkwnZ3.jpg The internet slows to a crawl and will eventually be inaccessible. I...
View ArticleClik here to view.
Re: Prevent/restrict access to the router from subnet.
Two ideas for you: Idea one, here's what I do to prevent access to other local subnets:- Create a ruleset for inbound trafic, here's mine for two guest subnets - copy my rules (I know that the ruleset...
View ArticleRe: Design Review / Sanity Check - Robust home network - ~$1,000 budget
Dave, I do check for updated firmware on new devices and will be using the wizard. It just seemed odd that the factory firmware was soooooo far behind current. Regardless all set on that front.
View ArticleRe: Design Review / Sanity Check - Robust home network - ~$1,000 budget
Thanks Bob. I may need to consider IDF if I put a security camera at the end of the drive but that is a 'someday' project. Thanks. I also need to say that as a new member this forum has made me...
View ArticleRe: Why is MASQ SNAT required for manual hairpin?
Packets from client to internal (web)server are NAT-ted:These packets start having your public WAN IP as destination. NAT on the ER translates destination IP into the local IP of your webserver....
View ArticleRe: Printers not showing under DHCP leases.
I consider manually managing printer IP addresses a good practice.But make sure to assign IP addresses outside of DHCP range, to avoid potential IP address conflicts.And if you do assign an address...
View ArticleFull Cone NAT for 3CX Server
Hello All, I am configuring a 3CX Server (v15 if that makes a difference) behind an ER PoE. I have 2 way audio, and most things are working fine, but the 3CX firewall checker shows a full cone NAT...
View Article