Re: Routing newbie, see if I have this sorted out
Plan looks relatively solid, though why not just keep eth1 on switch0, and not faff around with routing between wifi and LAN (at least with your trusted network)? Not that you cannot / should not do...
View Article4G/3G Connection options on Edgerouter X
Since the Edgerouter X only has ethernet ports, I'm looking for a low cost solution to provide a 3G/4G connection via ethernet. I know Sierra makes a 3G/4G gateway along with Cradlepoint but the price...
View ArticleRe: Issues Setting Up EdgeRouter and EdgeSwitch
16again wrote:Seems to me like internet access should be fine now on all VLANs. Don't bother about pinging ubnt.com , from my W10 PC it is also not pingable ->Getting specified VLANs out to the...
View ArticleRe: Polycom VOIP phone won't register - ER-8 Edgerouter 1.90
You disabled SIP where? Absolutely no firewall? What is your NAT config? Have you done a tcpdump to capture authentication info?
View ArticleRe: 4G/3G Connection options on Edgerouter X
Any carrier modem with an Ethernet port should do the job.
View ArticleRe: EdgeMax rescue kit (now you can reinstall EdgeOS from scratch)
I just needed to be a tad more forceful about it (thanks). The drive looks healthy in Windows (I have my usb serial-cat 5 on order as of today), but I figure there's no harm in trying to reformat it...
View ArticleClik here to view.
Re: Firewall Secure?
Thanks, your reply and BranoB's link are making things clearer. So I could keep that ruleset as is, for WAN-in, and then have another ruleset for WAN-out, to control what the ruleset for WAN-in,...
View ArticleRe: IPSec site-to-site with L2TP
any luck on this one? We are having the exact same issue. We had site to site working. Then we setup L2TP and it broke be site to site.
View ArticleRe: Firewall Secure?
The rules basically assume you trust everything internally, and trust that the sites internal clients connect to. Your router protection (WAN_LOCAL) is very important though. You can do much more to...
View ArticleEdgeRouter Lite Dropping Internet Connetion
Hi - I have seen a couple of posts about similar symptons. I just bought an EdgeRouter Lite - running 1.9. I have ETH0 connected to the WAN, ETH1 connected to a switch where everything hangs off. I...
View ArticleRe: EdgeRouter Lite Dropping Internet Connetion
Hi there, my best guess is that is has to do with a timeout occuring in the timer for the load-balance connection-check daemon. Are you using the feature? If so, try to assign a testing IP very close...
View ArticleRe: Network layout - 2 routers, 1 switch, 2 aps - a few questions
Thanks - I hadn't thought of the RIP option. As for the ASUS, I'm using it grudgingly - mostly I need it another switch on the first floor and AP it really only used by a few devices nearby (old lathe...
View ArticleRe: Network layout - 2 routers, 1 switch, 2 aps - a few questions
No actually just router mode with the 3 switched ports. I didn't realize the PoE could run as a switch... I know others can. Did you mean bridging in eth1?
View ArticleClik here to view.
Re: Routing newbie, see if I have this sorted out
Right now it's barely a config. Since I am waiting on that smart switch to come off of backorder, I can't do any vlans outside the router. I think you just made me realize that I could do something I...
View ArticleRe: Multicast, Sonos, Phorus & Play-Fi Broadcast 255.255.255.255: Discovery...
Sorry in advance for the super-noob questions that follow. My home network is setup as such: Modem --> ER PoE --> eth1 (LAN) --> switch --> wired clients (192.168.0.XXX)...
View ArticleRe: DNAT Issue (Can the source address be internal?)
When you 'allow all' on a given port (from Internet) there's no way to determine an attacker from a non-attacker. That is, unless you're using an IDS or some kind of active black/white list (which I'm...
View ArticleRe: can edgerouter max do this?
Perhaps use different ports with web forwarding. Could tie in with the mentioned proxy.
View Article