Clik here to view.
Port forwarding not working help
Hi,I am trying open a port for a game but I seem to be unable to get it to work and I require some help. Network SetupISP Modem -> EdgeRouter X (v1.9.0 ) -> NanoBeam 5AC 16 (v7.2.4) in Access...
View ArticleRe: VRRP Master does not send HELO multicast messages
So despite the firmware upgrade I still see the state changed to BACKUP in the keepalived.conf file on the "real" master node: vrrp_instance vyatta-eth2.14-14 {state BACKUPinterface...
View ArticleRe: commit-archive failing?
is there already one copy of the config on cerberus? If so, it's probably getting overwritten by the copy.
View ArticleRe: VRRP Master does not send HELO multicast messages
Can you send me your full config via hipchat.?
View ArticleRe: Nat hairpin behind double nated network
holy cluster, batman! This looks needlessly convoluted. You should probably straighten everything out, and stop letting the boss' "good with computers" 14 year old touch your network.
View ArticleRe: Port forwarding not working help
Mitka wrote:ISP Modem to EdgeRouter IP: 192.168.1.65/24 This is your problem right here - the ER should be getting the WAN IP, not some RFC1918 address from the ISP's device. Put their kit in "bridge"...
View Articleroute one device over ipsec
Hi All I'm trying to acheive a setup where I have a single device routed over an ipsec VPN tunnel - I've found a few tutorials to do this with openVPN but I wanted to take advantage of the acceleration...
View ArticleRe: Xbox 1 Strict NAT problem
I don't have any PS4s so I can't really give you a definitive answer. My best guess is that this is probably configurable, but which port to block is only a guess. If I had to guess I would choose one...
View ArticleRe: EdgeRouter stop working when using IPSEC VPN
How should I change my VPN setting for use VTI or GRE ( I don't know the difference beetween), Should I change the remote setting or only local? From the linked post I can understand that is not...
View ArticleHow to add second tunnel to ERX
I have an EdgeRouter X with working IPSec VPN to a Cisco RV320 in one office in Asia that I set from the CLI following this example that I found here: VPNset vpn ipsec auto-firewall-nat-exclude...
View ArticleRe: commit-archive failing?
dpurgert wrote:is there already one copy of the config on cerberus? If so, it's probably getting overwritten by the copy.They're timestamped. .......And I forgot that when I changed the case of the...
View ArticleClik here to view.
EdgeMax WAN traffic on eth0 WAY higher than LAN traffic
Hey guys, I apologize if this is obvious, but I am stumped. My WAN traffic (specifically transmit) is periodically going through the roof, sometimes to 300-500Mbits (no that is not a misprint...I...
View ArticleRe: EdgeMax WAN traffic on eth0 WAY higher than LAN traffic
I forgot to mention, often times the connection gets disrupted when it gets very high (200-300+ Mbits), and a router reboot is required. I may have the chicken and egg reversed, perhaps comcast is...
View ArticleRe: EdgeMax WAN traffic on eth0 WAY higher than LAN traffic
Any chance your router is hacked? Post output from ps uax. Also post your config to double check your firewall rules; show configuration | no-more. Do you have WAN_local firewall? Did you change the...
View ArticleRe: 'configure' command starts up with errors
vbash: declare: _vyatta_op_last_comp_init: readonly variable this is a good indication of busted USB disk (internal storage)Check your messages during boot and /var/log/messages for any indications of...
View ArticleRe: ipsec remote ip range not showing
See HERE (get access to Beta forum through your acccount settings).
View ArticleRe: 'configure' command starts up with errors
To replace the USB stick see EMRK thread or THIS simplified approach.
View ArticleRe: Edgemax Pro High CPU Utilization Issue
After The Changes Update: Up until load went to 200-240 Mb traffic the CPU utilization stayed below 90%. At 160 Mb constant traffic load smnpd became top running, and above 200 Mb traffic load snmpd...
View ArticleRe: How to add second tunnel to ERX
I've outlined the required changes, adjust rest of the settings as needed. set vpn ipsec esp-group FOO1 compression disableset vpn ipsec esp-group FOO1 lifetime 3600set vpn ipsec esp-group FOO1 mode...
View ArticleERL3, PPPoE disconnect problem
I've experienced this twice now: my WAN/PPPoE connection disconnects and ERL3 does not successfully reconnect. The first time, I just rebooted ERL3 and it started working again.This time, I did a...
View Article