2 hours ago it was fixed now he bricked your router?
It was suggested to upgrade to the non-GA firmware as it allowed PPPoE configuration. I did such. The router would not come back online. I rebooted it, it would not come online. I reset it, it would boot and then die, stop responding to ping and become inaccessible.
In the end I had to console in with a serial/RJ-45 Cisco cable.
The good news is after fixing everything and getting back on v1.8.5 and reconfiguring most of the settings I am getting 500Mbps. This is nearly half the speed I should but at least its progress.
Current config:
firewall {
all-ping enable
broadcast-ping disable
ipv6-receive-redirects disable
ipv6-src-route disable
ip-src-route disable
log-martians enable
name WAN_IN {
default-action drop
description "WAN to internal"
rule 10 {
action accept
description "Allow established/related"
state {
established enable
related enable
}
}
rule 20 {
action drop
description "Drop invalid state"
state {
invalid enable
}
}
}
name WAN_LOCAL {
default-action drop
description "WAN to router"
rule 10 {
action accept
description "Allow established/related"
state {
established enable
related enable
}
}
rule 20 {
action drop
description "Drop invalid state"
state {
invalid enable
}
}
}
options {
mss-clamp {
interface-type pppoe
mss 1452
}
}
receive-redirects disable
send-redirects enable
source-validation disable
syn-cookies enable
}
interfaces {
ethernet eth0 {
address 192.168.1.1/24
description Local
duplex auto
mtu 9000
speed auto
}
ethernet eth1 {
address dhcp
description Internet
duplex auto
firewall {
in {
name WAN_IN
}
local {
name WAN_LOCAL
}
}
speed auto
vif 201 {
pppoe 0 {
default-route auto
mtu 1492
name-server auto
password ****************
user-id gerasimatosnicho@qwest.net
}
}
}
ethernet eth2 {
address 192.168.2.1/24
description "Local 2"
duplex auto
mtu 9000
speed auto
}
loopback lo {
}
}
port-forward {
auto-firewall enable
hairpin-nat enable
lan-interface eth0
lan-interface eth2
wan-interface pppoe0
}
service {
dhcp-server {
disabled false
hostfile-update disable
shared-network-name LAN1 {
authoritative disable
subnet 192.168.1.0/24 {
default-router 192.168.1.1
dns-server 192.168.1.1
lease 86400
start 192.168.1.21 {
stop 192.168.1.240
}
}
}
shared-network-name LAN2 {
authoritative disable
subnet 192.168.2.0/24 {
default-router 192.168.2.1
dns-server 192.168.2.1
lease 86400
start 192.168.2.21 {
stop 192.168.2.240
}
}
}
}
dns {
forwarding {
cache-size 128
listen-on eth0
listen-on eth2
system
}
}
gui {
http-port 80
https-port 443
older-ciphers enable
}
nat {
rule 5010 {
log disable
outbound-interface pppoe0
protocol all
type masquerade
}
}
ssh {
port 22
protocol-version v2
}
upnp {
listen-on eth0 {
outbound-interface eth1
}
listen-on eth2 {
outbound-interface eth1
}
}
}
system {
host-name UBNT-Gateway
login {
user user {
authentication {
encrypted-password ****************
plaintext-password ****************
}
level admin
}
}
name-server 8.8.8.8
name-server 8.8.4.4
name-server 2001:4860:4860::8888
name-server 2001:4860:4860::8844
ntp {
server 0.ubnt.pool.ntp.org {
}
server 1.ubnt.pool.ntp.org {
}
server 2.ubnt.pool.ntp.org {
}
server 3.ubnt.pool.ntp.org {
}
}
offload {
hwnat disable
ipsec enable
ipv4 {
forwarding enable
gre enable
pppoe enable
vlan enable
}
ipv6 {
forwarding disable
pppoe disable
vlan disable
}
}
syslog {
global {
facility all {
level notice
}
facility protocols {
level debug
}
}
}
time-zone America/Los_Angeles
traffic-analysis {
dpi disable
export disable
}
}