Re: Multicast, Sonos, Phorus & Play-Fi Broadcast 255.255.255.255: Discovery...
See the first post in this thread...
View ArticleRe: OpenVPN Client Setup for Private Internet Access
Hi On the first page why did you change th 0.0.0.0/0 to 0.0.0.0/1 also why is the next hop the vtun0. I have set up ,any openvpn servers and clients (but I am new to ubiquiti) and the next hop is...
View ArticleRe: Synology OpenVPN Behind EdgeRouter
Hi Karog, I am not aware of it. I was thinking there were 2 options L2TP and PPTP only. IF you can share some steps that will absolutely great for me.
View ArticleRe: FRRouting Launch (Quagga Fork)
esseph wrote:Frr with support for the cavium SoC would be amazing Isn't a cavium soc a generic ARM core? (Not sure arm64 or arm7). FRR should compile and run on both. I'm testing at some extend on arm7...
View ArticleRe: Cable modem not detected on Edgerouter X
Did you manually set link speed to 10 or 100 Mb/s?If so auto MDI-X no longer seems to work, and you need cross cable.https://community.ubnt.com/t5/EdgeMAX/Router-to-EdgeRouter-X-Crossover/td-p/1363244...
View ArticleRe: Static route/wins/ etc
Focus on this post:https://community.ubnt.com/t5/EdgeMAX/Getting-UDP-Broadcasts-across-subnets/m-p/1937421#M161845 After installing helper relay config steps: Set service bcast-relay id 1 description...
View ArticleRe: Edgerouter PoE slows comcast residential internet, worked fine on...
I can't believe I forgot to attach the config, please forgive me.I checked the QoS section and found it still had limits set, ARG!!I deleted the QoS section and enabled IPv4 and IPv6 hw packet...
View ArticleStatic Route issues
Hi, So I've encoutered some issues with manually added static gateway routes where they either just don't work or work intermittently. The first one is at one site where their normal IP range is...
View ArticleRe: Edgerouter POE firmware 1.9.1 RANDOM reboots
Im having the same issue with 1.9.1.1 on an edgerouter poe. I thoought it was airflow/heat issue but I but a case fan on it and it is nice and cool but sitll random resets. I guess I will have to...
View ArticleSmartVPN
I saw come consumer grade router(xiaomi router) had implement a featured call "smart vpn". The ideal behind is to unblock the geo-restrict for end user outside the China to access the China content...
View ArticleRe: DHCPD Service Fail: configfile interface failed
crossfireprod wrote:Echoing @AvalonDanvers sentiment(s). Any word @UBNT-sandisn?The last thing I have done was give access to the ERL remotely. I haven't heard anything since in any capacity whether...
View ArticleRe: DHCPD Service Fail: configfile interface failed
We would highly appreciate if somebody could give us access to one of the affected devices.
View ArticleIPv6 dual stack issue
I can open that site http://dawson.meteomac.com, if I use this primitiv configuartion. ubnt@ubnt:~$ show configuration interfaces { ethernet eth0 { address 192.168.1.1/24 duplex auto ipv6 { } speed...
View ArticleRe: 1.4.0 - DHCP server hostfile-update feature not for static entries?
UBNT-stig wrote:...... We have talked about adding static-mappings to the host file automatically. That would be so great! As it is now, I have to create static host mappings for those hosts. That is,...
View ArticleRe: FRRouting Launch (Quagga Fork)
Although there are Cavium processors with ARM cores, I think the current UBNT routers use Cavium processors with a MIPS64 core. Some use standard mips (with Cavium extensions for their hardware...
View ArticleRe: Routing traffic from one subnet to OpenVPN
Hi mate,Thanks again for the help!In case you decide to continue to help me on my seemingly doomed quest - here's a redacted configuration after all the modifications we've come up with. Hopefully you...
View ArticleRe: Static Route issues
On port-forward tab, try removing nat-hairpin enable checkbox. It might confuse packets both entering and leaving the LAN interface, like traffic destined to 192.168.100.0/24
View Article
More Pages to Explore .....