Re: Edgemax- L2TP Server Setup For Client Use
Hi everyone, Just informing you that the EdgeRouter - L2TP IPsec VPN Server article has been updated and should provide all of the information you need to setup a L2TP Server. Best wishes.
View ArticleRe: Routing traffic from one subnet to OpenVPN
Would that not route all traffic out vtun0?
View ArticleRe: router-advert causes dhcpv6 prefix delegation to stop working?
We had several issues with handling DHCPv6 PD service when IPv6 RAs are also configured for the interface. It was not always clear which configuration has precedence. radvd.conf could have been...
View ArticleRe: EdgeRouter 1.9.1.1 WAN+2LAN2 Wizard bug?
Hi, Looks like an error. Which device/model? Just checked on ER-8 / 1.9.7alpha3 and it works correctly. Sandis
View ArticleRe: Routing traffic from one subnet to OpenVPN
Yes, but that's probably also the intentionThe rule you made says: The network 10.1.2.0/24 is behind the openvpn tunnel, whereas I assume 10.1.2.0/24 is on your LAN.
View ArticleRe: conntrack table being emptied on vpn changes
I can't remember that happened on me. But most of the times, I don't use the auto-firewall-nat-exclude option
View ArticleRe: Synology OpenVPN Behind EdgeRouter
I am no longer running OpenVPN on my synology. I too have moved to VPN on my ERL. When I was all had to do was port forward 1194 UDP from my ERL -> synology, and check the box on my Synology to...
View ArticleRe: router-advert causes dhcpv6 prefix delegation to stop working?
Thanks!Just to be clear, does that mean it only makes sense to set either DHCPv6 PD or IPv6 RA config? I.e. setting the IPv6 RA config will make the DHCPv6 PD config not matter?
View ArticleRe: Comcast IPv6 issues when hwnat enabled on ER-X
To clarify my prevous comment: I tried your exact config and no dice for me. It must be either my modem (sb-6183) or Comcast issue andthe er-x works fine with no hwnat (ipv4 and ipv6) as does my...
View ArticleRe: Synology OpenVPN Behind EdgeRouter
Maybe the static route is not needed for the OP, but he hasn't told us whether he checked the "allow clients to access server's LAN" option. I needed the static route in my configuration because the...
View ArticleRe: Need Help: Two ISPs setup
Thank's RedFive I did use the load balance wizards. I am trying to set it up like I had my Draytek where some computers will use eth0 (ISP 1) and some will use eth1 (ISP 2) depending on the IP address....
View ArticleRe: dnsmasq ignoring static-host-mapping config; resolving deleted entries
gfunkdave wrote:Did you flush the DNS cache on your computer?In Windows, it'sipconfig /flushdnsYes and I also restarted my computer and all my network devices. I do an nslookup on my Windows 10 PC or...
View ArticleRe: Need Help: Two ISPs setup
Yes, is feasible, what ip address do you have on eth0 and on eth1 ?Cheers,jonathaEdit ..Even better if you can post your sanitized config, connect via SSH, issue configure, then show, copy the config...
View ArticleRe: Comcast IPv6 issues when hwnat enabled on ER-X
I'd like to just report in that I'm using ER-X with a motorolla surfboard 6141 modem, with hwnat *off*, and it's working ipv6 just fine.Probably not useful, but an anecdote none the less.
View ArticleRe: DNSMasq DNS Not Working
I have a similar issue and can't get around it (2 for OpenDNS, 2 for GoogleDNS). I've tried all the CLI tweaks people have suggested but when I try to validate it OpenDNS says "nope, you aren't our...
View ArticleRe: Need Help: Two ISPs setup
My post don't seem to be showing so sorry if a doubbble post.. Thanks for helping Redfive firewall { all-ping enable broadcast-ping disable group { network-group PRIVATE_NETS { network 192.168.0.0/16...
View ArticleRe: Need Help: Two ISPs setup
This is more or less the half of the config ... Try this, show interfaces , show load-balance, show protocols static and post the outputs
View ArticleRe: Need Help: Two ISPs setup
ethernet eth0 { description WAN duplex auto poe { output off } pppoe 0 { default-route auto firewall { in { name WAN_IN } local { name WAN_LOCAL } } mtu 1492 name-server auto password bt user-id...
View Article