Re: EdgeRouter 8
Should i try to get a refund of the edgerouter 8? since the other ports will be no use to me? and get the 5 port with a 5...
View ArticleClik here to view.
Re: VISIO shapes/stencils
Hi ! Not sure if this is what you are looking for, but if you go to this article: Ubiquiti radio icons and images for diagrams (Visio, Gliffy, Omnigraffle, Illustrator, etc.) You should be able to...
View ArticleRe: qos priority on wan vlan
Hi,I've made test today with this line :configureset interfaces ethernet eth1 vif 2900 egress-qos "0:2 1:2 2:2 3:2 4:2 5:2 6:2 7:2"set interfaces ethernet eth1 vif 2900 pppoe 0 user-id titiset...
View ArticleRe: VISIO shapes/stencils
Not even close. The stencils in your "official" package are pretty much useless for a technical schematic. They are almost useless for everything else. A real set of device stencils would be 2D images...
View ArticleRe: IPSec WAN-WAN: anybody getting 40Mbps+ throughput?
Thanks! I will try this and report back here..
View ArticleClik here to view.
Re: VISIO shapes/stencils
Mmm okay yes, I know the kind you mean. Let me check if there's anything I can do about that. Walked straight into that one
View ArticleRe: VISIO shapes/stencils
Thanks. This would be hugely helpful. Like I said, you have the pictures... just need them in the proper format. :-)
View ArticleRe: How to configure two DHCP servers/pools on switched ports. (Public pool...
There has to be a solution to this. I was able to find cli code for this once a couple years back, but that code went away with an upgrade and I can not find it again after searching the forums for...
View ArticleRe: Load Balance and IPSEC Hardware Offloading
Can you also set an MTU on an ipsec interface? If so, what would that command look like? Another question: my provider (Swisscom) provides me with a FTTH connection. This is being converted to...
View ArticleRe: Getting UDP Broadcasts across subnets
Thanks a lot for your explanation! It's working fine for me now. Because I do have an ER-X and didn't know about the differences in cpu architecture compared to ERL, I wasn't able to troubleshoot...
View ArticleRe: How to configure two DHCP servers/pools on switched ports. (Public pool...
You can only have one DHCP server active on a given LAN. If I'm reading you correctly, you're saying you want to assign addresses from different subnets on the same subnet? This would seem to indicate...
View ArticleRe: How to configure two DHCP servers/pools on switched ports. (Public pool...
So Mikrotik has a "Next Pool" for this issue.It is common practice (so I thought) to have all radios on a private subnet and all customer routers to be on a public network. I have a routed network,...
View ArticleRe: Multicast, Sonos, Phorus & Play-Fi Broadcast 255.255.255.255: Discovery...
Hi because of 's great work I just realized that the reason for my bcast-relay not working was that I used your binary with an ER-X and didn't know about the incompatibility. Thanks a lot again for...
View ArticleRe: Multicast, Sonos, Phorus & Play-Fi Broadcast 255.255.255.255: Discovery...
Hi ,I'm not sure about the firewall as in my zone-based firewall the source zone to local (edgerouter) and from local to target zone directly allow any connection (as I use it to send wake-on-lan to...
View ArticleRe: VPN through edgemax
ubnt@ubnt# sudo tcpdump -i eth1 -n udp dst port 500tcpdump: verbose output suppressed, use -v or -vv for full protocol decodelistening on eth1, link-type EN10MB (Ethernet), capture size 262144...
View ArticleRe: Comcast IPv6 issues when hwnat enabled on ER-X
I have had some problems with IPv6 uploads from Android clients, for example at speedtest.xfinity.com, but not from Windows clients. This is true with every router/modem I've checked. I expect this is...
View ArticleRe: VPN through edgemax
found a thread on the forums here https://help.ubnt.com/hc/en-us/articles/115007396548-EdgeRouter-Forward-L2TP-Traffic-to-an-Internal-Server-Using-NAT-T I did everything in the instructions aside from...
View ArticleRe: QOS unfair Shaper Policy in Switch-Mode - Prio Employee not working
If eth port is under switch0....do NOT assign QOS policies or firewall rules directly to the eth port.At bootup, this will remove all your eth ports from switch0, and you're stuck with al ports without...
View ArticleEdgerouter Lite - IPv6 and DMZ
I have an edgerouter lite running 1.9.1.1 and I am running with a WAN, LAN, and DMZ interfaces. I have been able to succesfully get IPv6 setup and can get IPv6 addresses from my provider (TWC - now...
View ArticleRe: IPSEC Tunnel UP but no traffic
Yes, but it will come after rule 1, which allows established traffic. Anything that is not established and matched with rule 1 will then go on to rule 2, at which point it will be dropped. Since it's...
View Article
