Re: Simple WAN+2LAN not routing between 2LAN
In config, no firewall rules are in place on LAN interfaces, so they can't block traffic.You don't use firewall modify rules , so routing can't be messed up. Try disabling hairpin checkbox on port...
View ArticleRe: Simple WAN+2LAN not routing between 2LAN
This sounds like the routing problem is on your parents' LAN. If devices over there don't have a default gateway of 192.168.1.50--or their router doesn't have a route to 192.168.0.0/24 with a next hop...
View ArticleRe: Two edgerouters: 1 as router, 1 as VLAN switch
I'd take the "make the switch vlan aware" route. So all VLANs (300 640 , LAN , guest , iot ....whatever) are part of the switch.All VLANs (except 640) get their own switch0 vif x interface to add IP...
View ArticleRe: Two edgerouters: 1 as router, 1 as VLAN switch
Thanks for the quick reply! I'll try to go the route you suggested. I'm just not sure what VLANs to set where exactly. VLAN300 and 640 are delivered by my ISP. It seems to me that my Local network is...
View ArticleRe: Simple WAN+2LAN not routing between 2LAN
Tried disabling the Hairpin in Port forwarding but wasn't that. It turned out it was as suggested, the default gateway was set to 192.168.1.1 which would be my parents router but its not currently...
View ArticleRe: Two edgerouters: 1 as router, 1 as VLAN switch
You should get rid of the bridge altogether. All ERX1 ports including eth5 should go under the switch (keep 1 interface out during setup, and use it for fallback management interface) ERX2 will be...
View ArticleVPN through edgemax
Good Morning: Im having an issue, well a client is, having a VPN pass through our edgemax router. I havent played with VPNs at all he is using IKEv1 and is getting denied. Is there anything I should...
View ArticleI ran into a weird crash bug
I've been able to replicate this 3 times, just to verify that it's the case.This is tested on current build (I believe 1.9.1.1)Reset the edgerouter x Run the lan2 wizard. This is the one that sets a...
View ArticleRe: configure via plink (putty)
I have to login to read the solution, after which I get an access denies error
View ArticleRe: Simple WAN+2LAN not routing between 2LAN
If you can get into it, that ZyXEL does support static routing (according to the manual, but ymmv). Should be a pretty easy get.
View ArticleRe: Firewall rules for open air venue
You marked the wrong post as the solution, woops!
View ArticleRe: Two edgerouters: 1 as router, 1 as VLAN switch
Hi thanks for your help so far! I'm (slowly) able to piece things together.I've removed the bridge and added eth5 to the Switch (leaving out eth1 for fallback)Added the VIF to the switch (Switch0.1...
View ArticleRe: Two edgerouters: 1 as router, 1 as VLAN switch
HiJust a quick update, that I've got everything working! Thanks for the amazing help. For now, I've put everything under VLAN1, expect IPTV. I'll seperate this out later. They key tricks to making this...
View ArticleRe: Edgerouter Lite single thread upload slow with hardware offload enabled
Im afraid your issue does not seem to line up with the problem here. The issue is not capacity limitations but a mere problem with single thread performance and not general peak performance. Your issue...
View ArticleRe: restarting OpenVPN tunnel
I have been goofing with this script a little, saved the file as /config/scripts/piareset and I run it as a cron job every 5 minutes. It needs to be made executable for cron to run it (chmod 700...
View ArticleLink UP Link Down - Connection dropping
Hello, I've been having my WAN connection drop at lease once a day but mainly at night (usually when I notice it) and the logs shows some unusual activity. Anyone have any idea what could be wrong? My...
View ArticleRe: X509 site-to-site VPN with ADCS Certificates
I used a standard Windows Server Certificate Authority. However the logs looked much healthier when I changed to an unencrypted key. I also added the rightsourceip parameter. Have a look: 05[NET]...
View ArticleRe: VPN through edgemax
The only rule on the edgemax in NAT is to masquerade all protocols to eth1. I saw some other threads in forums suggesting a DMZ for this client. As we have 60 clients and growing going through this...
View ArticleRe: Comcast IPv6 issues when hwnat enabled on ER-X
Just a suggestion.... We've been having no problems with IPV6 and hwnat on Comcast in eastern Massachusetts with an ER-X running v1.9.1 and an Arris/Motorola SB6121 modem. One thing I notice in some of...
View Article
More Pages to Explore .....