Re: WAN Load-Balance and L2TP-over-IPsec - remote network does't respond via...
I checked you advise and in both route tables 201 and 202 - I have route to my L2PT client, but traffic no goes between L2TP client and remote network. (172.16.16.240/32 and 192.168.100.0/24) login as:...
View ArticleDebug on SFP interface?
Hi,I have connected my EdgeRouter X SFP to my local fibre FTTH to replace their "NTE". I used their MAC address and VLAN and simply swapped over. They gave me an IP as expected and it all worked...for...
View ArticleUnable to Block Google DNS on Switch0.100 VLAN100 for a Chromecast device ( i...
Hi My network looks like this: Ubiquity edgerouter poe 5 is on latest 1.9.1.1 ISP´s ONT Modem/Router connects from its ETH1ToEdgerouter POE 5 ETH0: ETH0 (this is my WAN interface)ETH2 ( switch port...
View ArticleRe: trying to configure EdgeRouter-PoE for persistent L2TP/IPSec connection
Yes, I realize that - let me clarify: I'm looking in to this because I'm aggravated about the current administration's laissez-faire attitude about the inportance of net neutrality - I find their...
View ArticleRe: trying to configure EdgeRouter-PoE for persistent L2TP/IPSec connection
Trouble with the approach is that you trust the VPN provider more than your ISP (they're easily just as untrustworthy, if not moreso).
View ArticleClik here to view.
ER-8 link light on eth5 with no cable?
Hi guys, I've had my ER-8 for about a year not +/- a month and today that eth5 link light is always on even if I don't have anything connected to the port. Has anyone seen this before? I've removed...
View ArticleEdgeRouter Lite kernel oops when bgp neighbor comes up 1.9.1.1
Sadly I don't have a console available yet, but when enabling bgp on a particular router it rebooted and the following was captured by the remote syslog server: kernel: CPU 0 Unable to handle kernel...
View ArticleRe: EdgeRouter Lite kernel oops when bgp neighbor comes up 1.9.1.1
I realised I could eliminate the number of routes by just filtering them on the other router. Still crashes. Annoyingly trying to change the config I ran into a bug with the vyatta config getting out...
View Articleedge router poe5 100% CPU
guys i need some assitance please....i have an edge router that seems to always reach and stay at 100% cpu usage when traffic leaving the wan is around 70Mbs and Up, when less bandwith is passing...the...
View ArticleRe: edge router poe5 100% CPU
Do you have the offload disabled or are you using some sorts of QoS ?Cheers,jonatha
View ArticleRe: edge router poe5 100% CPU
offload is disabled.....enabling it or disabling it didnt make a difference and no QOS
View ArticleHow to determine ISP IP lease time
As previously suggested by Ubiquiti I have tried the command show dhcp client lease to determine the ISP IP lease duration but it no longer works. When using show pppoe-client it appears to displays...
View ArticleRe: edge router poe5 100% CPU
eth0 and eth1 are load-balaced with eth1 for failovereth 2,3,4 are on switch0
View ArticleRe: NAT-PMP or uPNP on EdgeRouter?
I used this to turn on upnp2, wan on eth0, switch0 for eth1-4set service upnp2 listen-on switch0set service upnp2 nat-pmp enableset service upnp2 secure-mode enableset service upnp2 wan eth0
View ArticleDHCP Relay Not Working, Not Sure Why
Hey guys, was hoping someone could help me out here. I have a "production" network with DHCP, and I'm setting up a Plex/Media network in a separate VLAN. For whatever reason, I want anything in that...
View ArticleRe: DHCP Relay Not Working, Not Sure Why
I'd post the config but the 20k character limit is stopping me, even after I chop out a decent amount of stuff. I'm doing some offloading so I wonder if that's preventing this from working? Here's...
View ArticleIPSec site to site Dynamic DNS on both sides - Trouble on any Firmware above...
Hey guys, This issue seems to be well documented on the forums here. When running two sites where both sides are dynamic IPs, a IPSec tunnel will refuse to establish if using dynamic DNS on both sides....
View ArticleRe: IPSec site to site Dynamic DNS on both sides - Trouble on any Firmware...
Other site's config: ERCONDO firewall { all-ping enable broadcast-ping disable ipv6-receive-redirects disable ipv6-src-route disable ip-src-route disable log-martians enable name WAN_IN {...
View ArticleClik here to view.
Re: EdgeRouter has to be factory reset any time the ISP Modem restarts.
Idk if either of these is what your looking for.
View Article
