Complete crash of ER8
Good morning,I have a serious problem with an EdgeRouter 8, firmware v1.9.1.In a matter of weeks, it has spontaneously crashed 3 times. It is no longer possible to open by HTTPS, SSL or even answering...
View ArticleRe: Edgerouter X - can't get port forwarding to work again
What about firewall at destination host? (192.168.1.101)You have to make sure all those ports are open also there.
View ArticleRe: restarting OpenVPN tunnel
What about using OpenVpn's built in keepalive / autorestart features?set interfaces openvpn vtunX openvpn-option '--ping-restart 60' set interfaces openvpn vtunX openvpn-option --persist-tun set...
View ArticleRe: Edgerouter X - can't get port forwarding to work again
Let's put everyone's suggestions in one place so you can check them off: 1. Make sure you're not double natting. What is your ETH0 IP address?2. Do manual DNAT.3. Make sure your destination host's...
View ArticleClik here to view.
Re: Unbrick ER-X-SFP
... you both are very right on this.As a IT professional and dad with family I can agree with both ...time is usually not to spare. What I've done in situation like this, if the devices is cheap then...
View ArticleRe: Edgerouter X - can't get port forwarding to work again
I'de be curious to know if you enter the port numbers in the forward-to port if everything starts working.I tried that first even though the official documentation says it isn't neccessary. Neither way...
View ArticleRe: Complete crash of ER8
I would try reloading the OS first. If that doesn't work talk to support and see what their suggestions are, and then if there is no relief provided there I would RMA the unit.
View ArticleRe: Complete crash of ER8
You do have a firewall enabled on this and your management ports are NOT open to the Internet, right? You are also NOT using ubnt/ubnt for the user and password, right?
View ArticleRe: IPV6-PD on Edgerouter X
your firewall rule may need to have a different MAC address: "3": { "action": "drop", "log": "enable", "source": { "address": "fe80::e2b9:e5ff:fe14:10c0" } },to find this mac address you need to try...
View ArticleRe: Comcast IPv6 issues when hwnat enabled on ER-X
I'll have to check it with hwnat. CPU usage is fine w/o hwnat (of course ipv6 is also).When I get a chance, I will check and report back. Fred B.
View ArticleRe: IPV6-PD on Edgerouter X
It also seems as though you're missing a few key things, ESPECIALLY 'prefix-only' (add in those highlighted bold) dhcpv6-pd { pd 0 { interface switch0 {host-address :1 prefix-id ::1 service slaac }...
View ArticleRe: EdgeRouter X Failover question
I might not have had the router configured correctly when I did the load balancing to get the Dynamic DNS working. I just remembering that everyone on the forums said that because it was local and not...
View ArticleRe: Comcast IPv6 issues when hwnat enabled on ER-X
What I have found is something in HWNAT is causing the DHCPv6-PD advertisements (source port 547/dest port 546) to be discarded silently. BTW I have this specifically permitted in a firewall rule and...
View ArticleRe: IPV6-PD on Edgerouter X
, : You do not need firewall rules to stop this link local address on the WAN? This was a workaround for a very specific issue where the ERX was seeing responses from two DHCP servers, and was...
View ArticleRe: Beta access not working
Hi Everyone, We have fixed the issue that was afftecting the beta signups and forum access issues. Should anyone still have issues please let us know by replying back here. Thanks,David
View ArticleRe: Preventing ER GUI timeout/logoff
L9000 wrote:To date I haven't been able to get snmp working on the ERL. I've tried: set services snmp community [string] client [ip address] but always receive "invalid node" errors. Also, I'd like to...
View ArticleRe: WAN Load-Balance and L2TP-over-IPsec - remote network does't respond via...
For the router on the other side of the vti tunnel is there a route back to 172.16.16.x going back to this router?- yesubnt1@ubnt1:~$ show ip routeCodes: K - kernel, C - connected, S - static, R - RIP,...
View ArticleRe: What are the recovery options on a EdgeRouter X?
You have only loaded kernel in order to get file partitions for LEDE ready.After that you have to copy sysupgrade LEDE image and use sysupgrade -n sysupgrade.binOff course replace sysupgrade.bin with...
View ArticleRe: What are the recovery options on a EdgeRouter X?
ok - thanks gents. I have to do some work at the moment, but will carry on, and see if i can move this to completion. So - I am at the point where I can get LEDE running with a command prompt. I have...
View Article
