Re: edgerouter er-8 sends ip over wan from DHCP server
frits1980 wrote: how can i prevent this? Put the ISP router in bridge mode and plug everything in after the edge router -Jamie M.
View ArticleRe: Transparent ER-X with Smart Queue
So your wanting a bridge then? But its not hardware offload yet and you can QoS with Smart Queue on the interface thats part of the bridge I've tested this on my ERL.
View ArticleRe: ER-X+UAP, request config help, LAN1/SSID1 private, LAN2/SSID2 public Wi-Fi
Of course yes, even though with the Unifi controller you can declare a SSID as 'guest', (some ebtables chains with their rules are added to thist SSID for prevent, by default, the access to the whole...
View ArticleRe: How to correctly configure hyperV and Edge router networking
Thanks for the quick reply.I created a new vlan with ID - 2updated vlan ID in the VM settings in hyperv to 2Still its not working :-( I have attached screenshots in case I am doing something wrong...
View ArticleRe: How to correctly configure hyperV and Edge router networking
Try to set a static IP in your VM to take DHCP out of the picture. See if you can ping the ER at 74.1 and then out to the internet What NIC are you using in your server?
View ArticleRe: How to add my static IP address to an eth interface ?
After I set the NAT destination to my static ip all webpages are like this... Your connection is not privateAttackers might be trying to steal your information from www.google.com (for example,...
View ArticleRe: How to add my static IP address to an eth interface ?
you're doing something very very wrong. Update the router to 1.9.1.1, and run the "WAN + LAN" setup wizard. That'll set you up with a "basic SOHO Router". The exact specifics depend on your router...
View ArticleRe: ER-X+UAP, request config help, LAN1/SSID1 private, LAN2/SSID2 public Wi-Fi
In Step 4 (https://help.ubnt.com/hc/en-us/articles/218889067-EdgeRouter-How-to-Protect-a-Guest-Network-on-EdgeRouter) would this make sense? Instead of...set interfaces ethernet eth1 vif 10 firewall in...
View ArticleRe: IPsec s2s using FQDN not working after upgrade to 1.9.0
- Just weighing in on this - I too have this issue on 1.9.1. It works if I have an IP address entered at each end for the peer, but not if I use a hostname. I need to use a hostname here as one of the...
View ArticleRe: How to make IPv6 DNS requests to use my preferred IPv6 DNS servers on...
Hi, Your devices are probably receiving Comcast's DNS servers via slaac. These commands should fix it:$ configure# set interfaces ethernet eth0 dhcpv6-pd no-dns # commit # save
View ArticleRe: ER-X+UAP, request config help, LAN1/SSID1 private, LAN2/SSID2 public Wi-Fi
provided that vif10 is the 'guest' lan, absolutely.
View ArticleRe: HELP: Windstream Fiber PPPoE (No Modem) Slow Download / Great Upload // ER-8
djGrrr wrote:can you connect a pc directly to the ONT and setup the PPPoE connection there? then test the speed you get, if you can't get the full speed at that point, then the isp or the ONT is at...
View ArticleRe: Newb on Edgemax Pro8
There are a few how-tos relating to segregating networks from each other (some of the better ones reference segregating guest networks, but it's the exact same idea). Phone posting so I can't dig one...
View ArticleVLAN Routing on EdgeRouter
Hello, Hoping for a push in the right direction: My goal is to have a VLAN for surveillance cameras which shouldn't reach the internet, but is routable on the internal network to/from any internal IP,...
View ArticleModify TTL
Is there any provision to modify the TTL? I'm trying to accomplish something like: iptables -t mangle -A FORWARD -s 192.168.1.2 -j TTL --ttl-set 64 I looked at Change TTL on Edge Router Lite but was...
View ArticleRe: How to make IPv6 DNS requests to use my preferred IPv6 DNS servers on...
Thanks for your suggestion! I very appreicate it! I tried your suggestion and when I run the following command, I now seeing this...ubnt@ubnt:~$ show dns forwarding nameservers...
View ArticleRe: How to make IPv6 DNS requests to use my preferred IPv6 DNS servers on...
I wonder if the Comcast DNS servers are still ending up in your router advertisements? Can you check the contents of /etc/radvd.conf for any RDNSS entries?
View ArticleIs EdgeRouter ER-8 good for hotel?
I currently have a little WatchGuard XTM25 in a hotel client of mine; one interface is Comcast, the others are FrontDesk, Sales, and Hotspot. There are typically about 150 IP addreses running through...
View ArticleRe: How to make IPv6 DNS requests to use my preferred IPv6 DNS servers on...
oh, I am not aware of this /etc/radvd.conf file. Looks like the Comcast's IPv6 DNS is indeed inside that file. ubnt@ubnt:/etc$ cat radvd.conf interface switch0 { # This section was automatically...
View ArticleRe: HELP: Windstream Fiber PPPoE (No Modem) Slow Download / Great Upload // ER-8
Have you tried using a different port on the edgerouter?
View Article
More Pages to Explore .....