Re: Losing WAN ipv6 route on reboot + help on specific ipv6 broadcast settings
Hey Thanks for the reply. I did what you said and it appears to be working now. I found that my ipv6 connectivity wasn't actually up for a good 4 minutes or so even though the gui showed the addresses...
View ArticleRe: CHAP authentication failed - Centurylink Gigabit Fiber
Did you ever find a solution? I'm having the same issue.
View ArticleHow to add my static IP address to an eth interface ?
I want my ipv4 ip to be 86.127.219.21 (my static ip) not a LAN ip like 192.168.1.xx When I pug my internet cable in my PC directly I receive this static ip 86.127.219.21When I plug my internet cable in...
View ArticleRe: Newb: Two ISPs, two OpenVPNs, torrents direct
So my current thinking goes like this:- default via VPN1- squid1 as transparent proxy and on port XXX (it checks the table 'local' and assigns the interface of my ISP if found; port XXXX for...
View ArticleUnable to get data from FTP Server
hi, we have installed a FTP Server in our LAN (eth7) but cant get Data to a PC in Networt eth2 (DMZ). Connect and Directory Changes works well, but "Dir" and get / pull Data doesnt work....
View ArticleRe: [BUG] regex not found error in firewall statistics with plus sign in rule...
+++PUSH+++ Error still present in v1.9.1.1.
View ArticleRe: Dual WAN - Use WAN 1, then when maxed, used WAN 2.
To route specific clients to a different gateway you need to set up policy based routing. By default routing works by destination IP only. With PBR you can add a seperate routing table with its own...
View ArticleRe: Dual WAN - Use WAN 1, then when maxed, used WAN 2.
Hi, first, I assume you want to "spill over" upload traffic to WAN2 if upload bandwidth on WAN1 is at max. Here's just a quarterly-baked idea, but maybe it's a start: You can set a limit of hits per...
View Articlesquid / squidguard stop working
hi, after upgrading from 1.8.5 to 1.9.1.1 the squid / squidguard service crashed from time to time. the same issue we have in any firmware since 1.8.5. http connections are borken, https works fine....
View ArticleRe: Unable to get data from FTP Server
Did you try disabling the firewall on the PC itself in DMZ ?
View ArticleRe: Unable to get data from FTP Server
hi, the windows firewalls are disabled. eth2 hosted the webserver with access from the interneteth7 hosted the fileserver with ftp server the webserver should get data from internal network over ftp....
View ArticleRe: VPN IP sec won't establish
On R1 the nat-t seems enabled,nat-traversal enablewhile on R2 doesn't ...Cheers,jonatha
View ArticleRe: How to add my static IP address to an eth interface ?
The ER is doing everything correctly -- by virtue of "how the internet works" , you typically only get one publicly-routable address from your ISP, and then have to NAT to a RFC1918 subnet. Depending...
View ArticleRe: squid / squidguard stop working
Check how large the squid logfiles are AND that they're "still there" (with the right user) after an upgrade.
View ArticleRe: squid / squidguard stop working
the logs are available when the squid crashed. the squid runs a few days / hours before he crashed. ubnt@SW1375:/var/log/squid$ ls -al total 228 drwxr-xr-x 2 proxy adm 100 May 11 12:28 . drwxr-xr-x 11...
View ArticleRe: VPN IP sec won't establish
Indeed, thank you, i fixed it, but still no vpn established unfortunately.
View ArticleRe: Domain based routing
randychou wrote:iptables seems to just do it for the first request to the host instead of every time someone requests it and the IP changes. That's common behaviour. When you add rules to iptables and...
View ArticleRe: Setting VLAN's with ERX broke it completely
To update, the problem was with the DHCP server, not the transit/communication between VLAN's.Currently, the VLAN's are operating normally with ERL + USW and I've successfully segmented off my Server...
View ArticleRe: Unable to get data from FTP Server
It seems your FTP uses active mode. In this mode there are two connections with opposite directions. First the control connection that gets initiated by the client (client:49959 <--> server:21)....
View Article
More Pages to Explore .....