Re: EdgePOE-5 Router
Post your configuration.Sounds like the network on switch0 isn't set up right, so running the WAN+2LAN2 wizard then reconfiguring your PoE setting might solve your problem (but I don't know for sure).
View ArticleRe: Help with Edge Max and 3 poe access points
Running the WAN+2LAN wizard should get you up and running with WAN on eth1 (port 2).
View ArticleEdgeRouter Pro - how to disable routing
Hi@All, the subject seems a little bit funny but we have multiple Edgerouter Pro new and we will use them for wan-side routing only. Therefore we configure eth0 for managemnet (Pivate-Lan 192.168.x.x.)...
View ArticleRe: Help with Edge Max and 3 poe access points
These are different to a 4 port ISP/SoHo 4 port router. There are only 3 true switch ports on the PoE 5. These are eth 2, 3 & 4. Use WAN+2LAN2, disable bridging and eth0 as your WAN port. Bridging...
View ArticleRe: EdgeRouter Pro - how to disable routing
Create a firewall ruleset, e.g. name Management-In, with a drop policy. Then assign it to eth0 for the direction in. configure set firewall name Management-In default-action drop set firewall name...
View ArticleRe: EdgeRouter Pro - how to disable routing
thanks for your prompt reply and help. I'll do so tomorrow.Andreas
View ArticleDomain based routing
Hi, My apologies if this has been answered. But I couldn't find this answer. Is there anyway to have a specific domain, such as *.apple.com, go through a different routing? We have a proxy/security...
View ArticleLosing WAN ipv6 route on reboot + help on specific ipv6 broadcast settings
Hi all, I seem to be losing my WAN address for eth0 on reboot. This causes my devices to not be ipv6 connectable. In my GUI, it looks like eth0 was released from its ipv6 and wasn't able or didn't try...
View ArticleDHCP issue fixed only by reset but why?
So I have a bridge and it set to allow DHCP through it. My ISP VM only allows rebinding by broadcast to renew the IP what was happening and I tested this locally too with a DHCP server was the ERL was...
View ArticleRe: VPLS over GRE (Somethings not working)
You should be aware that there's a known bug with the LDP/MPLS implementation in edgemax:...
View ArticleER-X+UAP, request config help, LAN1/SSID1 private, LAN2/SSID2 public Wi-Fi
Hello,This is my first time configuring an EdgeRouter X (v 1.9.1.1) and a UAP AC M. Up until now, I have only been familar with some of the AirMAX products. I'm hoping to get some help with the...
View ArticleRe: Setup two routers on different subnet
Hi 16again, I tried but with no success. Below is my configuration on both routers. Can you please help ? R1: 192.168.1.0/24 Network firewall { all-ping enable broadcast-ping disable...
View ArticleRe: ER-X+UAP, request config help, LAN1/SSID1 private, LAN2/SSID2 public Wi-Fi
You may take a look at this 3d, as a clue, and this is even more important .....Cheers,jonatha
View ArticleRe: Requests/suggestions for new hardware models
Is this the correct location to post Ideas? Do you all UBNT have a published roadmap for products?
View ArticleRe: ER-X+UAP, request config help, LAN1/SSID1 private, LAN2/SSID2 public Wi-Fi
Run a wizard first, then proceed from there. That'll at least protect your network from the outside world.How I'd do it:-Put all of your LAN ports on switch0 (wizard probably already did this).-Add a...
View ArticleRe: Emerging Threats Blacklist
WaterSide I looked at all your items on GIT. I read the readme. Is it possible you could write a guide in more detail. I am trying to read the post here and figure it all out. However due to the...
View ArticleI keep Dropping internet connection on my Edgemax Pro
For some reason my internet connections keep dropping on both inbound (for management) and outbound and My ISP claims its the router not obtaining the IP address from the modems. I have 2 modems with...
View ArticleCisco 2600 to Edge Router PRO
This might be a dumb question, but are there any utilities or scripts that will help me setup a new edge router pro from the config file of an ancient cisco 2600 router? It's not a typical setup and...
View ArticleRe: VPLS over GRE (Somethings not working)
Thanks. Im aware of the bug. I would still like to figure this out.
View Article
More Pages to Explore .....