Re: Load Balance with IPSEC and dynamic adresses
Could you show what kinda of sticky command you would write. lb-local is disabled now. Best regards//Marcus
View ArticleRe: OpenVPN on Edge Router - How to renew an expired CA?
Check the script that generates them -- I don't think CA.sh generates those (can't recall, tbh).
View ArticleRe: Edgerouter POE firmware 1.9.1 RANDOM reboots
I have the same router and fw but after about 14 says it goes off line and poe shuts off on all ports. I am on solar with a Tycon DCDC 1224 70 watt converter running the router and a PBEM5-400. The...
View ArticleRe: EdgeRouter X Will Not Power on with UAP-AC-PRO POE Injector
Thanks, I did do that and it worked. I was hoping I'd be able to use the injector. I've opted for a properly rated power supply to accomplish this. Thanks again.
View ArticleRe: GRE tunnel from an ERL to a Linux server
On ER, tryencapsulation gregre-bridge is layer2 bridge gre is layer3
View ArticleERPOE-5 Goes dark looking for input
ERPOE-5 (FW 1.9.1) Goes dark sometimes after about 2 weeks and this time I was troubleshooting load balance with failover not working and noticed all traffic was routing over a non ISP WAN (eth0) and...
View ArticleRe: Smart Queue seemingly not working for Steam downloads
Hello, I have another update. I did everything I said I was gonna do and unfortunately nothing changed. So I started doing some more research about various anti-bufferbloat scripts and found other...
View ArticleRe: Comcast IPv6 issues when hwnat enabled on ER-X
Bump. Any word on whether the new 1.9.7 alpha addresses this?
View ArticleRe: EdgeRouter X Will Not Power on with UAP-AC-PRO POE Injector
What do you mean when you say "I've opted for a properly rated power supply to accomplish this?" If you bought a 24V power adapter for the ER-X or a 24V PoE injector it still won't work for you. The...
View ArticleIPv6 address assignment to clients
Greetings,I have my HE IPv6 tunnel working and ping6 tests on the router work. How do I make the router's DHCP server hand out IPv6 addresses? I got this far, but there are errors and I can't find any...
View ArticleRe: GRE tunnel from an ERL to a Linux server
Isn't layer 3 what I'm looking for though, since I really only want to route IP traffic? I re-read the guide and it looks like I might be able to just use the local IPs for the two machines, I'll try...
View ArticleRe: EdgeRouter X Wall Mount
Drew this up based on the measurements, not sure if it will work until I get my 3D printer back at home.http://www.thingiverse.com/thing:2249029
View ArticleRe: EdgeRouter X Wall Mount
I think ur gonna need cutouts on the sides or you'll block air flow.
View ArticleRe: OpenVPN client and server on same router?
Sorry for the slow reply. Work's been crazy.. Unfortunately reading that link didn't quite fit or I'm misreading it. It looks like that example is using different ethernet ports on the router to go to...
View ArticleRe: OpenVPN client and server on same router?
I already told you what to do in post 10 above. Move firewall in modify PIAVPN_ROUTE from eth0 vif 3 to eth1 and remove source stanza in nat rule 5001. And why do you even have vif 3?
View ArticleRe: bricked edgerouter er-lite3
I did, and it worked for a little while .. then I started getting A12 errros . My unit's ddr is hosed :/ . Thank you for the info!
View ArticleEdge Router ER-X
I'm setting up my home network so that I can SSH into my linux box. I need to be able to send a Wake-on-LAN packet to the broadcast IP (xx.xx.xx.255) for my private network. That comes in on port 9 and...
View ArticleRe: OpenVPN client and server on same router?
That's weird.. the VPN showed connected but TBD for any details on it. Disabled / Renabled and everything magically is going through the VPN now which is huge compared to previously!! Thank you so much...
View ArticleRe: Smart Queue seemingly not working for Steam downloads
Try adding hostFairQueue to the mix, so bandwidth is shared more equal amongst internal hosts.It's available in basic and advanced queue
View ArticleRe: EdgeRouter X Wall Mount
Maybe add some clickable locking mechanism, so ER-X remains in place when pulling a cable...or when mounted cables going downward.
View Article
More Pages to Explore .....