Re: IGMP/Muticast for BT YouView
Hi there, is it possible to explain a bit further by means of a config example? you say about assigning the eth0 an ip address, mine is currenly setup as pppoe0 as the interface (wan) but iptv channels...
View ArticleRe: EdgeRouter X Wall Mount
maybe use modeling clay to make a reverse mold of the screw holes that you can then measure? if you make one (a printer file) it'll probably be of use to the community. Best,jeff
View ArticleRe: VLAN Routing between interfaces issue
I got it working on my test environment but...my production environment is an EdgeRouter POE and as far as I can tell the VLAN Aware isn't an option with this model.
View ArticleRe: Noob Questions: Dual Router setup
You've just moved the data harvesters from "your ISP" to "NordVPN" (and that's not even considering your search engine). I know I'm being a pessimistic about it - but VPN just makes two hosts...
View ArticleRe: Forward of port 80 leads to router admin page viewable via site domain
Is it mostly always Eth0? (POE Passthrough is disabled in my case). You can see what being a technologist without her own network to play with for an age and a half has done to me. LOL
View ArticleEdgeRouter Pro DHCP-Relay not working
Hello everyone, We're having issues with DHCP-Relay on our EdgeRouter Pro. Here's a general idea of our network setup: 2 subnets: 192.168.0.0/24 and 192.168.1.0/24Server 2012 DHCP server:...
View ArticleRe: Can't install build-essential on OS v1.9.1
tester252 wrote:It's take many time, but I installed build-essentials and compiled squid-3.5.24 and it's work.Is there a reason you needed to compile this yourself? EdgeOS already includes squid....
View ArticleRe: DHCP Relay Not working
Hello guys, I see you were able to figure this problem out and it seems quite similar to an issue we are experiencing. If you have a chance, can you take a look at this thread and see if you have any...
View ArticleRe: Newbie looking for advice on how to secure EdgeRouter PoE etc
Hi George, you might want to consider segmenting your home LAN into seperate subnets (Layer 2 separation using VLANs) for added security.These are the VLANs that I use:- A management VLAN with no...
View ArticleRe: Forward of port 80 leads to router admin page viewable via site domain
eth0 is a default for one of the wizards. If that's not your WAN interface, obviously change it to suit your setup ...
View ArticleRe: EdgeRouter Pro DHCP-Relay not working
I've attempted using the "relay-agents-packets discard" relay option per this article. It's not working but i'm not sure if I am using it correctly or if it is what I need to solve the issue.
View ArticleRe: EdgeRouter Pro DHCP-Relay not working
I'm not a networking guy. I assume the router eth 5 is plugged into a switch and that the AP is plugged into a switch. If that's the case why have a relay for 192.168.0.0 set up on the router as the...
View ArticleRe: VLAN Routing between interfaces issue
Correct, an ER-5-POE does not do VLAN aware. This means that all traffic will be sent from switch0 as untagged / PVID 1tagged {... all other vlans you've configured ...} You will need a downstream...
View ArticleRe: Noob Questions: Dual Router setup
I believe that the only NAT that's going on is from the ERX. The Buffalo is running OpenVPN in DD-WRT. Are you suggesting that I congure the VPN on eth3 of the ERX instead of running it on the Buffalo?...
View ArticleRe: Edgerouter X SFP issues after power failure.
abruptly killing the power on UBNT kit (incl. USGs) is not very good for them -- you should invest in a battery. Most likely, it's corruption somewhere -- a power-on reset may correct that, or...
View ArticleEdgePoint Router 6-Port v1.9.1
Where is the settings for Spanning Tree in EdgePoint Router 6-Portv1.9.1 GUI ?
View ArticleRe: EdgeRouter Pro DHCP-Relay not working
You are correct, we can remove DHCP relay for eth5 and the AP does pick up an IP natively through the switch.However, removing DHCP relay for eth5 causes DHCP relay for eth6-192.168.1.X- to stop working.
View ArticleRe: Noob Questions: Dual Router setup
It's more of a question of do you trust them more than you trust your ISP than anything. In my case, I trust "VPN anonymizers" as much as I trust my ex , so ... I'm not sure how the buffalo device...
View ArticleRe: EdgePoint Router 6-Port v1.9.1
IIRC EP-R6 (and both ER-Xs) doesn't support STP. It's has to do with the switch chip architecture internally - UBNT has talked about seeing it it can be implemented, but I don't think there's a time...
View ArticleRe: Edgerouter X SFP issues after power failure.
I had a really nice UPS, unfortunately it appeard to have failed this morning I'm going to buy a new one this week. I've done a "Power-On" reset, and it does successfully boot to the default settings....
View Article
More Pages to Explore .....