Re: Possible bug smart queue ER Pro 1.9.1
I'm under the impression this is normal behavior when you apply to LAN or vlans interfaces. Try and apply your ISP down/up to the eth0/WAN interface and it should correspond correctly....
View ArticleFRRouting Launch (Quagga Fork)
Thought this may be of interest to some users here / the mods: https://frrouting.org/
View ArticleIKEv2 switching to IPv6?
I was setting up an IPsec VPN between two EdgeRouters, both on EdgeOS 1.9.1 and noticed a very strange thing. When set to ikev2, no traffic would flow. Checking each router, I noticed the following in...
View ArticleRe: Ziggo static IPv6
There is (well, kind of):Subnet: 2001:41f0:XXXX::0ISP Gateway: 2001:41f0:XXXX::1Usable Range: 2001:41f0:XXXX::2upwards toEnd range: 2001:41f0:XXXX::fffeBroadcast: 2001:41f0:XXXX::ffffSubnet: /48 When...
View ArticleRe: EdgeRouter X SFP leaking MAC addresses
cmaeder wrote:I didn't, as to me it looks as it would only be relevant for the 1.8 series of the firmware.Nevertheless, the problem occures during normal operation and not during boot. The uptime of my...
View ArticleRe: Edgepoint r6 POE
From standart POE (45;78 for power) to Edgepoint eth0 (POE in) is lenght cca 6m (Cat.6, Shielded, grounded). From Edgepoint to AP's its 2m (Cat.6, Shielded, grounded)... if i replace edgepoint with...
View ArticleRe: EdgeRouter X block all incomming traffic expect a couple of ips
You may want to have a look at Layman's firewall explanation
View ArticleRe: UDP packet loss with EdgeRouter Lite
The faster feeling makes sense if there's underlying packet corruption/loss. The TCP connections that your browser makes would have to detect the loss and retransmit, which would slow the loading of...
View ArticleRe: Edgerouter Lite - Getting rid of Bell Canada's Homehub2000 ( Internet AND...
pjaneiro wrote:Hi, I'm at a loss, I's used different configs from around here and for the life of me I can't seem to get Fibe TV going I'm using an edgemax X-SFP router and I have two issues First,...
View ArticleRe: Private Internet Access Open VPN - Step by Step Configuration
Thanks . For the incoming connection do I need to do DNAT/Port Forwarding? I currently only have one host that needs certain traffic to go around the VPN, but would like it if the traffic could just be...
View ArticleRe: UDP packet loss with EdgeRouter Lite
Looks like 1.9.7alpha1 has landed in the beta forum (https://community.ubnt.com/t5/EdgeMAX-Beta/EdgeRouter-alpha-release-v1-9-7alpha1/m-p/1887554#U1887554), has anyone got a chance to test it yet?
View ArticleEdge Router Pro Slow Upload Speed
Older Edge Max 2 - 3 years old. v 1.8.0 I'm wondering if someone might chime in on this and help me figure out why this Edge Max exhibits slow upload speeds. It is on a Comcast link ~ 100 down ~ 10 -...
View ArticleRe: UDP packet loss with EdgeRouter Lite
New 1.9.7alpha1 firmware image has been release today and it has two enhancements that might improve packet-loss issue on Cavium-based routers (ER, ER-pro, ER-lite and ER-poe). I'm saying mightbecause...
View ArticleRe: EdgeRouter X block all incomming traffic expect a couple of ips
My suggestion should work for you then. If you want certain external IP addresses to have access to specific computers on your network (web servers, etc.) then you'll need port forwarding rules as...
View ArticleHow to add rules when using public ip to access inside servers?
Hi, I already add port forwarding rules for inside service(switch0), these rules point WAN to at least 8 different inside ip addess/port, it is working fine, when I access using public ip/cell data. My...
View ArticleRe: How to add rules when using public ip to access inside servers?
You have to enable Hairpin NAT on the Port-forwarding page.
View ArticleMapping external ports to LAN on other side of vti?
I've been banging my head against a pretty hard wall for a couple of weeks now. I have a vti tunnel between two locations. All traffic on the remote subnet is routed through the tunnel. Say my WAN IP...
View ArticleOpen source project bounty for VPN configuration
Here's a github issue offering a bounty for instructions on how to configure an EdgeRouter Lite to route all internet traffic from a LAN over an IPSec VPN.
View ArticleRe: Routing vs Interface Traffic - Where is return going?
Any thoughts on this one? Another weird situation is I can ssh/web/https to all the 10.1.200.* items, but when I try to ssh in and do an iperf from the main server to the device, I can connect to the...
View ArticleNet Monitor to just pull the info from the bar graphs ERX
Good Day All, I just wanted to check if there was any sort of monitoring solution that can pull just the data from the bar graphs in the ERX. Have tried PRTG, but for some reason it doesn't want to...
View Article