Re: Comcast IPv6 issues when hwnat enabled on ER-X
I tried v 1.9.0. Hwnat still disables ipv6. I flashed back to the current version and disabledhwnat. I will standby for further info.Fred B
View ArticleRe: Edge Router Pro Routing Problem from Subnet to Subnet
Hello, i test today many things but i can not ping a Computer on a other Subnet!from the Router CLI Console i can ping each Computer in each Subnet,but when i make a Ping to a Computer in another...
View ArticleRe: How to tell which devices are on which interface vvia GUI?
Which ER model do you have?On models without a switch, your LAN interface is the actual interface you've configured for LAN i.e. eth1. On models with a switch, your LAN interface, if you configured...
View ArticleRe: EdgeRouter X bricked ?
My EdgeRouter works again. I left it off a day or so, tried the reset again and it worked. Don't know what I did differently. But I don't dare to edit anything in the settings other than the standard...
View ArticleRe: Edge Router Pro Routing Problem from Subnet to Subnet
if you connect via cli, which is the outpput ofshow ip route In the upper right corner, Toolbox, packet capture, selec (first) interface eth1, packet limit 10, proto icmp, from the eth1 try a ping to...
View ArticleRe: How to configure IPSEC protected GRE tunnels ? (Urgent)
This should get you pointed in the right direction. Urgent?https://help.ubnt.com/hc/en-us/articles/204961754-EdgeRouter-Layer-2-bridge-over-GRE-tunnel
View ArticleRe: How to configure IPSEC protected GRE tunnels ? (Urgent)
and thishttps://dn42.net/howto/EdgeOS-GRE-IPsec-Example
View ArticleER-X-SFP power poe problem
Hi ,Maybe someone has the same problem. I use ER-X-SFP 5port full 5 port poe powering 5 ubiquiti devices.Sometimes one of these decvices doesnt respond and then i must of/on power on selected port and...
View ArticleRe: IPv6 and bgp neighbor update-source
kwal wrote: EdgeOS' bgpd is apparently not respecting the update-source, and is choosing a different address as the source address for BGP traffic! If update-source only works for IPv4, how can I...
View ArticleRe: EdgeRouter PoE switch
HI, I currently have one on my desk and after few days of testing and reading posts about ES-8-150 i must send it back to my local resseler. Theres is no watchdog, no power-cycle option no power info...
View ArticleRe: EdgeRouter PoE switch
oh i forgot U have CLI commands Yeah but when You have much time You can look for something in CLI manual but its not easy. So as a local Small Bussiness switch it can be ok but as a WISP switch NOT.
View ArticleAply firewall policy tio VPN IPSEC
Hi All,I have three vpn ipsec. One of these vpn have vti interface asing to routing and firewall this is OK.But, I need to apply firewall policy to VPN without vti interface. I can't have create vti...
View Articledns options ignored from config
Hi there,I try to setup zone transfer with additional dnsmasq options auth-* but it is complete ignored.set service dns forwarding options auth-peer=10.206.250.204,172.31.254.1 set service dns...
View ArticleRe: Edge Router Pro Routing Problem from Subnet to Subnet
Hi Ok i tested this..i have attached 2 Printscreens, one with the show ip route and one with the icmp i start the Paket Capture tool and send a ping from eth1 to eth2 and i become some Traficyou can...
View ArticleRe: ER-X-SFP power poe problem
I have actually seen this too. Usually happens after a mains power cycle when using an ER-SFP with many of the ports POE. Shutting off the POE, then turning it back on, fixes. But it should be...
View ArticleRe: Noob ER questions
If all you need is 24V PoE, then yes the ER-X-SFP will be better for you. In order to get the best performance out of the ERPoE-5, you won't be able to use eth0 or eth1 (effectively making it a 3 port...
View ArticleRe: Edgerouter pro CPU
I am not assuming, it was getting processor bound at times. I tried replacing an enterprise router with the edgrouter pro and I give it kudos. It was able to perform better than the cisco 7206vxr...
View Articleuser level operator
Hi thereI try to restrict access for operator and use preseted level operator. How can this user change there own password?how I can specify which commands can be executed through CLI for operator level?
View Article
More Pages to Explore .....