Re: Help with multi subnet routing
the ER X SFP should have a static route 192.168.0.0/24 -> 192.168.1.2
View ArticleRe: Error message in 1.8.5
I think i found it.When you have a BGP peer in inactive state you get this error.When i shutdown the session the error messages stops. Kind RegardsM
View ArticleRe: Error message in 1.8.5
ehsab wrote:BGP-3: [SOCK CB] sock_getpeer() failed (134:Transport endpoint is not connected), FD(18)This message indicates that bgp session with peer was dropped and restarted. It is a know issue and...
View ArticleClik here to view.
Re: Error message in 1.8.5
ehsab wrote:When you have a BGP peer in inactive state you get this error.When i shutdown the session the error messages stops. I would like to clarify - is it expected that your BGP peer is in...
View ArticleRe: 48VDC Power Adapter for EdgeMax Router POE?
Hey Ben, I just picked up an ERPoe-5 in the UK (great unit btw). It came with a 24v EU plug supply too though. I think it must be old stock as it had EdgeOS 1.2 ;-). I was hoping to run 48v poe to my...
View ArticleRe: upnp nat problems
You didn't specify, but it looks like you're running an ER-X. With your speeds, you probably don't need hwnat. If you want to play around with Smart Queue (QoS) or Traffic Analysis you'll probably...
View ArticleEdgeRouter X powered by POE
I am trying to power an Edgerouter X from a Linksys SRW224P switch. I have connected to ETH0 from the switch. The port shows active and power being supplied but the router will not power up.Any...
View ArticleRe: EdgeRouter X powered by POE
I believe that switch only does 802.3af PoE. The EdgeRouter X can only be powered by 24V passive PoE. You'd need one of Ubiquiti's 24V power injectors (like what comes with the UAP-AC-LR and...
View ArticleRe: Error message in 1.8.5
Hi,Yes, it is expected, the bgp session is not yet configured on the other peer. Kind RegardsM
View ArticleClik here to view.
Re: EdgeRouter X powered by POE
d-m-z wrote: I believe that switch only does 802.3af PoE. The EdgeRouter X can only be powered by 24V passive PoE. You'd need one of Ubiquiti's 24V power injectors (like what comes with the UAP-AC-LR...
View ArticleRe: ER-8 firewall, when to use NEW state?
Hey , thanks for your reply. I'm using that rule above in a zone based firewall but I wanted to test what you said so I implemented ACL rules instead. Here's the rule sets and interfaces configured....
View ArticleRe: Consequences when running the load balancing wizard
I currently moved 1 WAN connection back onto the old Watchguard firewall untill this dual WAN is correctly support.
View ArticleEdgeMax freezes
Hello, The EdgeMax that's been used for our unifi wireless access points network has been jammed/frozen 2 times today. The only led that's still lit is the one from the power, all the rest is out. Is...
View ArticleRe: ER-8 firewall, when to use NEW state?
Just tested. On my test bench ERL, I didn't have LAN rules applied previously. Executing commands below definitely breaks internet access for clients. set firewall name LAN_IN default-action drop set...
View ArticleRe: Consequences when running the load balancing wizard
If you just add 2 addresses to a single interface, you can use NAT rules to use both IP addresses.Offcourse no load balance is involved, but using one gateway, there is nothing to balance.
View ArticleClik here to view.
LAN to Lab subnet
Hello everyone, I'm trying to setup a home lab using a pretty uncommon network installation and I'm not able to make it work. I'm here:LAN <= LABI need:LAN <=> LAB Here is the setup:The lab...
View ArticleRe: EdgeMax freezes
apparently this box had the default ubnt/ubnt account still there so I guess someone got in and messed with it. I added a nat rule on the wan for https/443 pointing to a non existing IP.A firewall rule...
View Article
