Re: [Help] Route Traffic for One Device from WAN 2
If you need that the host 192.168.1.10 uses eth1 as main interface, and eth0 as failover interface,configure set load load-balance group A interface eth1 set load load-balance group A interface eth0...
View ArticleRe: Slow speed port 21 and 8899
Bridging is officially NOT recommeded because it "greatly reduce performance" -- see EdgeRouter-Creating-a-Bridged-Interface
View ArticleFirewall - allow DNS (port 53) inbound
Hello community! Scenario: External DNS for master domain, but I want to allow inbound DNS for a subdomain by NS record pointing to an insdie IP (10.x.x.x) for the subdomain with our AD server(s). My...
View ArticleRe: edge router poe 5 reset loops?
Hi.Octeon ubnt_e100# setenv ipaddr 192.168.1.20 Octeon ubnt_e100# setenv serverip 192.168.1.10 Octeon ubnt_e100# setenv ethact octeth0 Octeon ubnt_e100# tftpboot 0...
View ArticleRe: Firewall - allow DNS (port 53) inbound
If you also use a DNAT/port-forward rule, and the server allows connections from remote/public networks, should be ok ...Cheers,jonatha
View ArticleRe: Firewall - allow DNS (port 53) inbound
Do i NEED a DNAT rule/port forward? I currently do not have any port forwarding. This is our primary router/firewall. So making changes is not somehting I want to take lightly.I need to understand...
View ArticleRe: AP-AC-Pro on another subnet when connected to EdgeRouter
I reset the router, and set it up using the Basic Setup again. After plugging the AP-AC-Pro into the eth4 port, wired internet changes from "network 3" to the AP "name". When I IPconfig it also shows...
View ArticleRe: Firewall - allow DNS (port 53) inbound
The WAN_IN ruleset is for packets destined to internal hosts (think at the FORWARD chain, in iptables), if you only allow, thanks to the firewall rule, to the inbound packets with dst port 53 to be...
View ArticleRe: edge router poe 5 reset loops?
Hi. I unplugged the power and started the router again whis this result :-( Same issue again. Processing PHDR 0 Loading 665180 bytes at ffffffff80800000 Clearing 12dd40 bytes at ffffffff80e65180 ##...
View ArticleRe: UDP port 5060 no longer working in port-forward
firewall { all-ping enable broadcast-ping disable group { address-group VPN_HOSTS { address 192.168.6.9 address 192.168.6.4 address 192.168.6.8 address 192.168.6.10 address 192.168.5.3 description...
View ArticleRe: EdgeRouter Lite GRE Tunnel
Got it working! I misread you again... I added the same PBR rule for eth2 as well and now its working! Thanks a lot! modify EXTRAIP { enable-default-log rule 30 { action modify log enable modify {...
View Articleedgerouter lite issues
Hey guys, This is my first post.I've recently switched from a VM running OpenWRT to edgerouter lite to get full gig speed (with the vm i was getting 700 mb maximum) I am from romania and i'm using...
View ArticleClik here to view.
Re: EdgeRouter Lite GRE Tunnel
For reference to other people trying to do the same the complete config (slightly redacted).. It now both does NAT to an internal server on eth1 and allows a dedicated server on eth2 with a direct...
View Articleedgerouter4 with att gateway
att has deployed ftth in my neighborhood. i'm looking to a reseller so that i can buy only the service i need. 60mbps and static ip. the reseller states that att usually deploys arris bgw210 or pace...
View ArticleRe: Firewall - allow DNS (port 53) inbound
Thank you. Problem is that even before I can get it to a host, the firewall is still filtering it (port 53 is not open from the internet inbound) Once I can get the packets inbound, then I can get it...
View ArticleRe: IPv6 DHCPv6-PD Broken on ERX, firmware 2.01?
I'd like to report that this is still an issue with 2.0.3. Same problem. I tried offload off and on, so see if there was a difference. No change, no IPv6 connectivity.
View ArticleRe: Weird issue with IP suite with random clients
No dice. With firmware 1.10.9 the trick of starting a packet capture does not clear it up as a bonus.The only solution I found was to flush the arp/neighbor cache and restart dnsmasq. Is there anything...
View ArticleRe: Azure VPN BGP site-to-site not working
Thank you for your help. My configuration was actually correct.I was just having trouble verifying that it was working. I really appreciate your time on this. For anyone in the future that is...
View ArticleRe: EP-6 Crashing
https://community.ubnt.com/t5/EdgeMAX-Updates-Blog/Recalling-EdgeRouter-firmware-v2-0-1-for-ER-X-ER-X-SFP-and-EP-R6/ba-p/2753322...
View Article
