Re: ERLite‑3 slow performance, offload issues ?
To the best of the my understanding, that means you have requested to enable offloading (the first command) but it has not actually been enabled (the second command) most likely because of other...
View ArticleRe: ERLite‑3 slow performance, offload issues ?
Thanks, I had flow accounting configured, removed it and it solved the problem.
View ArticleRe: Getting dhcp address from ISP is slow
wrote:Hi , Can you try running a tcpdump packet capture on the WAN interface to see if there are any replies to the DHCP requests? After rebooting the device, run the following command from the...
View ArticleRouter trafic for netflow
I've got a small wisp setup and right know i have and edgerouter x/sfp router in switch mode as the first devicemy isp has given me /27 network i would like to set it up so a can pass the data through...
View ArticleRe: IPSEC VTI tunnel stops on regular intervals
I did eventually figure this out. First I had some mild success by enabling NAT-T but I'd still have the regular drops. Then while working with a completely unrelated tunnel on a different device I...
View ArticleDouble nat issue with plex
When I run plex and check if remote access is available, initally it says it can access remotely but then comes up with the following error: It looks like your server may be connected to the internet...
View ArticleTrying to delete a firewall rule
If I run 'show firewall' I ge tthe below output: IPv4 Modify Firewall "SOURCE_ROUTE":Active on (eth1.11,IN)rule action proto packets bytes---- ------ ----- ------- -----10 modify all 0 0condition -...
View ArticleRe: Trying to delete a firewall rule
figured it out: delete firewall modify SOURCE_ROUTE
View ArticleRe: Simple, modern IKEv2 VPN using PSK and no certificates
See my following/second post if you encounter this problem! This post describes an issue which you will most likely get, when you don't configure your Clients correctly!...
View ArticleEdgeRouter X reboots once a week
HI, I have a ER-X router, running v 2.0.1, and i've noticed that it reboots once a week (Saturday morning in my case) with no apparent reason. i've configured it to send logs a linux machine in my...
View ArticleRe: I think my Edge Router is bricked
I used a RJ45 to DB9 to a DB9 to USB serial cables that work with my pFsense and Sonicwall serial consoles so I am fairly sure that the cables are correct, I even tried it with and without a null...
View ArticleRe: EdgeRouter X reboots once a week
Try 1.10.9. 2.x causes issues with ERX's. Lots ofevideince in the 2.0.1 thread.
View ArticleL2TP with openVPN on vtun0
I have had L2TP configured for vpn remote access for a while. I recently started configuring an openVPN connection with vtun0. I have successfully configured policy based rules to limit the traffic...
View ArticleRe: [Help] EdgeRouter-X: Wake on LAN (WOL) doesn't work after a while
Hi, If you could hep me.
View ArticleRe: L2TP with openVPN on vtun0
After further investigation, it looks like ALL access from the WAN to internal is blocked with vtun0 enabled. None of my port forwarding is working while the tunnel is enabled.
View ArticleRe: L2TP with openVPN on vtun0
Can you try by adding the rule 5, in the firewall modify PBR policy, for exclude lan-to-lan from PBR ? See here, step 4 for hints.Cheers,jonathaEdit .. if not present, add the directive route-nopull in...
View ArticleRe: Simple, modern IKEv2 VPN using PSK and no certificates
An update from my side:My setup has been correct..I found out that I didn't configure my iPhone and Android Smartphone correctly.Modifying and using the iOS Profile you attached did however work! Seems...
View ArticleRe: EdgeRouter X reboots once a week
wrote:Try 1.10.9. 2.x causes issues with ERX's. Lots ofevideince in the 2.0.1 thread.I went over the 2.0.1 thread, but didn't find something similar to my case...
View ArticleRe: No frames passing - EdgeRouter Infinity (ER-8-XG v1.9.7+hotfix1)
I had the same issue, until I purchased the Ubiquiti SFP+ optic and works fine now.
View ArticleRe: data usage monitoring using vnstat (cli only) HOWTO
Look at this for monitoring 1 ip address https://help.ubnt.com/hc/en-us/articles/360008732414-UNMS-NetFlow
View Article