Re: intervlan routing with openvpn
try push-route instead of push-router btw: If you only type a few chars, and use tab for autocompletion, you won't run into errors like these
View ArticleRe: intervlan routing with openvpn
Can you post the output ofconfigure show interfaces openvpn
View ArticleRe: intervlan routing with openvpn
Yeah, is right, as you can see in the previous post, is push-route ... , not push-router.Cheers,jonatha
View ArticleRe: intervlan routing with openvpn
Works now! thank you all for this great and quick support!!
View ArticleWireguard - Load Balancing - Packet leaves wrong interface
Hey there, we're using an ER3-Lite to load balance between our two 100k/40k PPPoE connections. That works very well and we haven't any issues with the internet connection. Let's assume the topology...
View ArticleClik here to view.
Re: not seeing gigabit 1000 options?
Thank you for thatSo I just switched to FIOS gigabit service.Getting about 800mb into the Edge but only just over 100 out?Total novice here so I don't know what I am doing.Screen shots of config as I...
View ArticleEdgeRouter PoE DHCP Client not working
I'm facing the issue, that DHCP Client (address dhcp) isn't working with some interfaces/dhcp servers. I'm currently not able to swap interfaces to find the exact cause. In my Setup DHCP Client is...
View ArticleRe: EdgeRouter X Upgrade failed. Read-Only File System Error
Does anyone/UBNT have a boot file? I want to try to flash uboot with:add system boot-image force
View ArticleRe: EdgeRouter 12 Bonding
Considering IPv4 offloading is not working for me, I would say no. Once they fix offloading and bonding on switch ports everything I used on the device will work.
View ArticleRe: not seeing gigabit 1000 options?
Why are you using a BR0 (Bridge) for your Local?????? Your just killing your performance.....add ETH1-4 to Switch 0, delete the bridge and put your local IP on the Switch0 interface.
View ArticleRe: not seeing gigabit 1000 options?
wrote:Why are you using a BR0 (Bridge) for your Local?????? Your just killing your performance.....add ETH1-4 to Switch 0, delete the bridge and put your local IP on the Switch0 interface.Note only...
View ArticleER- X SFP - Offloading issues
So I have setup an ER-X SFP as my primary router but my LAN-LAN (switch0) performance is sub-par when compared to my Asus N56U (w/ Hardware Ofloading enabled).I have a 200 Mbps down and 20 Mbps up FTH...
View ArticleRe: not seeing gigabit 1000 options?
You are correct I passed right over the ER5 part. Still killing performance. Keep the APs on Switch0 break ETH1 out of BRO0 and put it on its own subnet and then setup some rules to allow the two...
View ArticleRe: Wireguard - Load Balancing - Packet leaves wrong interface
You have lb-local enabled, seems your causing your own problem.
View ArticleClik here to view.
Re: ER- X SFP - Offloading issues
wrote:So I have setup an ER-X SFP as my primary router but my LAN-LAN (switch0) performance is sub-par when compared to my Asus N56U (w/ Hardware Ofloading enabled).I have a 200 Mbps down and 20 Mbps...
View ArticleRe: ER- X SFP - Offloading issues
NAS (eth3) ----- Router ----- Computer (eth4) Rx - 268 Mbits/sec Tx - 404 Mbits/sec CPU Usage ~ 60%
View ArticleRe: EdgeRouter X Upgrade failed. Read-Only File System Error
A filesystem is mounted read only usually by system when it's detected to be 'dirty' ...it needs check and fix errors. The issue may be 'soft' and you can fix it with appropriate fsck or 'hard' that...
View ArticleRe: Homenetwork Setup Assistance
I would recommend to read this website first: https://www.handymanhowto.com/ubiquiti-edgerouter-lite-soho-network-design/ Can you elaborate a little bit more on what you are trying to achieve?
View ArticleClik here to view.
Re: EdgeRouter X site-to-site VPN NAT and L2TP
Hi, We started from 0, we made the peers in the GUI and added extra config through the CLI. We added the remote-id, encapsulation and dead-peer-connection but it still wont budge. It looks like they...
View ArticleRe: ER- X SFP - Offloading issues
The only thing I can think of its a autoconfiguration mismatch? what's output of "show interfaces ethernet physical"
View Article