Re: Route traffic to 4G
The firewall policy should be applied to the vif 50, not on the wan interface . What exactly are your needs ?
View ArticleRe: Help with routing
How is R2 connected to R1 (what IP, etc)? Unless you have a requirement for the 2nd router, you could simply connect your 2nd switch into a different port on R1 and simplify things.
View ArticleRe: Route traffic to 4G
To be able to control on the 172.16.50.0/24 network what traffic is allowed and not allowed back into the other networks. For example I want to block ICMP. But I might want to allow access to a media...
View ArticleWrite Darkstat log to /var/log/darkstat
So I've been toying around, and trying to get darkstat.db on tmpfs rather than the onboard flash.tmpfs is essentially ramdrive, right? For some reason though, darkstat service isn't, or is unable, to...
View ArticleRe: I want to put an Edge Router and an Edge Switch in my lab
Thank you for this comprehensive answer! It appears that the ER-X is the way to go, as it’s performance seems to be better than the ER-Light, especially with encrypted loads. I understand what a...
View ArticleRe: Help with OSPF
Strange - I must be missing something. I have both Site B and Site C with OSPF enabled. switch0 interface added, no authentication, redistribute connected and static selected, normal area 0.0.0.0 with...
View ArticleRe: Are there open or documented dyanmic DNS protocols?
wrote: I am currently looking at among others NoIP (one of the provides prominently documenting their protocol) and integrating that into my existing change-ip-at-registrar-via-their-api.py code.I...
View ArticleRe: Edge Router Lite Newbie IpV6
Unless someone here already knows what Zen do, then yes. For example, do they use prefix delegation, what size prefix do they send, or do they just give you a single /64 subnet ? You could contact Zen...
View ArticleClik here to view.
Re: Disable a physical port via GUI
Hi, Does anyone have any ideas of how to physcally disable an Eth port from the routing engine. The GUI disable does nothing? Thnaks in advance
View ArticleClik here to view.
Re: Some VLAN considerations
Hello Right : I want to separate the admin interface from the rest.I'm going to do what u ask and i'll post it here after. Don't worry if I make some time to answer Kids at home ! Regards Charles
View ArticleRe: Are there open or documented dyanmic DNS protocols?
wrote:I think you are confusing the two. EdgeOS is not providing any form of "notification" itself. DDNS is a generic "dynamic DNS" - it is not any one particular solution. EdgeOS works with many...
View ArticleClik here to view.
Re: Disable a physical port via GUI
Always best to post your config I would guess that eth3 is part of switch0 - remove it from the switch0 interface and it should stop passing traffic. When you have these ports as members of the...
View ArticleHow to block internet, but allow Dropbox?
So I've learned in the Unifi section, that the USG isn't able to do this. Is the EdgeMAX router able to block the internet, but allow Dropbox to a VLAN? In short, I'm trying to create a dedicated VLAN...
View ArticleRe: Installed wrong OS package 'Illegal instruction'
Hard reset worked, after being able to browse in the gui again I restored a backup. Thanks a lot!
View ArticleRe: Route traffic to 4G
Currently, unless some kind of 'Guest policy' maybe on AP's (if there) you shoud be able to access all the VLAN's, from the 172.16.50.0/27 network, since the firewall policy isn't correctly applied,...
View ArticleRe: Are there open or documented dyanmic DNS protocols?
Could you simply replace ddclient with your own program named ddclient? Since EdgeOS is invoking ddclient when it thinks the IP address has changed, it would instead invoke your program which would...
View ArticleRe: Help with routing
Start with setting static routes for your networks on each router: On R1, you need a route for 192.168.2.0/24 through 192.168.100.2On R2, you need a route for 192.168.1.0/24 through 192.168.100.1
View Article