Re: Updated Google Fiber + EdgeRouter Lite / PoE IPv4 & IPv6 config.boot and...
Hi, I've had Google Fiber (in Austin) since last July using an Edgerouter PoE 5, with just ip4. About a month later I decided to get ipv6 working and used sjjenkins's configuration example to get mine...
View ArticleRe: Setting up and isolating 2 networks
tridy wrote:Thanks for the reply. I thought that the bridging is needed between the switch0 and eth1 (since they are on different networks) so it would be able to access the internet throught eth1,...
View ArticleRe: My EdgeMAX X SFP got hacked (exploit in 1.9.0 firmware?)
raynak wrote: Then, the router didn't start up - didn't get an IP through DHCP, so I entered a fixed IP and tried to connect to 192.168.1.1 - and got a splash screen with an error message from an ASUS...
View ArticleProblem PortForwarding with LoadBalancing
Hi, I have a problem with Portforwarding within Loadbalancing. Our Setup:Two Static IP-Adresses on Eth0 and Eth1 both with PPPoeLAN on Eth3 10.0.1.1 to Hardware Firewall 10.0.1.2 (IPFire) Problem: When...
View ArticleRe: Setting up and isolating 2 networks
Thanks a lot for the explanations!I will get rid of vlan, and work on adding the proper gateway.Is it going to be the gateway from the incoming eth0, like 192.168.1.1, and then all subnets will use...
View ArticleRe: L2TP DHCPv6 "Interface is not configured for DHCP"
ChaseHaddleton wrote:...Is there anyway to setup the L2TP VPN to listen on an interface which uses DHCPv6? No, L2TP supports IPv4 only.
View ArticleEdge Router dhcp relay and DPI
Hello here is what I would like to achieve.My goal is to use the edge router do do DPI as transparently as possibleNow here is my detail goal I have a VDSL router. This VDSL router has 2 interfaces1...
View ArticleRe: IPv6 Setup
is correct. When using SLAAC a Router Advertisement (RA) is definitely needed. But, with the EdgeRouter implementation an RA is created with the service slaac command within the WAN interface...
View ArticleRe: QOS Settings for VOIP
Thank you for your reply Advocate99.If I set the theoretical total bandwidth in those settings, will be it considered as the "default" bandwidth and limit the speed if the theoretical is lower than the...
View ArticleRe: ER-X - Corrupt downloads
One more update since I managed to get my hands on an Edgerouter Lite to test: Replacing the ER-X with the ER-L, the ER-L was also corrupting downloads of larger files (e.g. 80MB) from the internet to...
View ArticleRe: Edgerouter ER3-Lite Firewall matching destination network group
Use commands below to check if iptables generated rules and address objects are as expected:sudo ipset -L sudo iptables -L -n -v
View ArticleRe: Edge Router dhcp relay and DPI
DHCP relay on ER looks fine, (and probably works fine). However, the DSL modem must have DHCP scopes configured for your internal networks, otherwise it won't hand out addresses to them. Using PBR,...
View ArticleUsing an EdgeRouter Lite to bond and load balance two WANs (VDSL)
Hello, I've just joined and despite my searching in the forum I haven't found my issue addressed. Mind you, this could well be due to the technical exlanations I've read going well over my head. So, I...
View ArticleRe: ER-X - Corrupt downloads
I would like to sumarize the symptoms:Does setting on MSS to 1402 on ER-X fully solves corrupt download issue?Does setting on MSS to 1402 on ER-Lite fully solves corrupt download issue?Do you observe...
View ArticleRe: Problem PortForwarding with LoadBalancing
can you check if return packets are sent out on correct wan interface?Usesudo tcpdump -i pppoe0 -n -v tcp port 8080or its counterpart on pppoe1
View ArticleRe: Problem PortForwarding with LoadBalancing
Hi, thanks for your Reply I guess you are right. While listening on pppoe1 and request on pppoe0, pakets are sniffed on pppoe1 which seems to be the problem. Hmmh. Any idea why? Thanks for your help...
View ArticleRe: Compound NAT solution?
Still trying to determine if I am able to use switch0 for my SNAT and DNAT in/outbound interface, or if I have another problem. ports 1-4 are one switch0, with 4 devices (PC, 3 UUT interfaces) on those...
View ArticleRe: L2TP DHCPv6 "Interface is not configured for DHCP"
The interface is also assigned an IPv4 address by my ISP, is there a way to get L2TP to use that address instead?
View ArticleRe: Compound NAT solution?
Put the PC on switch and the uut port that needs NAT on eth0. Then set up a dnat rule with outbound interface of switch 0
View Article
More Pages to Explore .....