Re: Private Internet Access Open VPN - Step by Step Configuration
varelse have you made any progress with this script? If I run this configuration of the script: added the --insecure option to the curl command #!/bin/sh#### If you would prefer not to use a hash of...
View ArticleRe: IPsec Site to Site, one way traffic
Thank you. That worked perfectly.It just creates the appropriate IP tables right?I will do a before and after compare on the tables and learn what is going on. Thanks again!
View ArticleRe: OSPF Loadbalancing 2 work this ?
What u think worked this solution now to transport 1 gbit , without bottlneck on routers capacity ? with this solution i think i have a layer 2 load balanced vlan transparent link with 4...
View ArticleRe: configuring an interface with a "deprecated" / preferred_lft 0 ipv6 address?
I played around with extending the vyatta-cfg templates to support this: # sed -i 's/^multi:$/tag:/' /opt/vyatta/share/vyatta-cfg/templates/interfaces/ethernet/node.tag/address/node.def# mkdir -p...
View ArticleRe: QOS Settings for VOIP
Hello, I wonder why it is needed to set upstream and downstream bandwidth. Why not simply set the bandwidth needed for the phone to work? For my VoIP I would only need 100kb. So why not doing like...
View ArticleRe: Understanding IP Addressing on Physical Interface vs. Virtual Interface...
Thanks for the advice. Yes, our sites are pretty small. I've been numbering the eth0 interface as say 192.168.13.1 and the UniFi switch as 192.168.13.2. Would the 192.168.13.2 constitute a "de-facto"...
View ArticleRe: Emerging Threats Blacklist
Hello, I must thank sandstheman for his script.Now I wonder how I can see that it works.As you can see I do not get any error messages anymore.## Blacklist 1 / Blacklist 2 ##I have two full lists of IP...
View ArticleRe: Google IPv6
Are you aware that IPv4 DNS can handle IPv6 queries? It is simply an AAAA record.
View ArticleRe: Known Issues of EdgeMax Series
Here's one more confirmed bug ldp cleaning full table and mpls forwarding table
View ArticleRe: Emerging Threats Blacklist
Platon12 wrote:Hello, I must thank sandstheman for his script.Now I wonder how I can see that it works. This script does the same as the several other scripts previously listed in this thread, and this...
View ArticleRe: Firewalling OpenVPN Site-to-Site
Or ? Or anybody? I have no idea what else to try to get this working.
View ArticleRe: Google fiber with EdgeRouter Lite
Hi . The current version of my config.boot files already have the options added by Atlantisman's TV scripts (which I later modified a bit) already included. See the section of the article that says:...
View ArticleRe: Known Issues of EdgeMax Series
Hi UBNT-Fenng, Thank you for your work for updated EdgeMax.I have ERX and have issue about 2 about IPSEC. Support IPSEC (IPv4 over IPv6). Now I need to additonal GRE (IPv4 over IPv6) under 1.9.1, it...
View ArticleSetting up and isolating 2 networks
Hello.2 days of frustration imI am here crying for help.I would like to set up my router so that:1) 2 (eth1, eth2) devices are in one network accessing internet from eth02) 3rd device (eth3) is on a...
View ArticleEstablished/Related Rule Allows NEW TCP Connections?
In the rule HOME_IN I was successfully able to block addresses on eth2 (192.168.2.1/24) from talking to eth1 (192.168.1.0/24) However, when I try to add an ESTABLISHED/RELATED rule to HOME_IN to punch...
View ArticleEdgeRouter X SFP v1.9.1 IP forwarding
Hi I can not setup my EdgeRouter X SFP and need some help.so my config is here in photosSo I have UBNT AC-500 on eth0 with IP 192.168.20.28 and 192.168.20.29 but I can not connect on it.what should I...
View ArticleRe: Setting up and isolating 2 networks
Have you seen the knowledgebase article on this subject?https://help.ubnt.com/hc/en-us/articles/218889067-EdgeRouter-How-to-Protect-a-Guest-Network-on-EdgeRouter If you have already tried doing what...
View ArticleRe: Established/Related Rule Allows NEW TCP Connections?
I'm not a firewall rules guru, but my guess is that it's something to do with your specifying all four stateful options. The stock Ubnt configuration just shows "related enable; established enable" and...
View Article
More Pages to Explore .....