Routing multiple ERLs behind OPENvpn?
Hi ,I would like to kindly ask you for your help. I run three OPENvpn servers... on the main site ( ROUTER A) with public IP and another two sites that are connecting to this ROUTER A (ROUTERS B, C)...
View ArticleRe: Private Internet Access Open VPN - Step by Step Configuration
Right, I think I also referenced earlier in the thread a couple times that it was a python script when it is a bash script. I am going to mess around with uploading to the USGP4 and seeing if I can get...
View ArticleRe: EdgeMax POE with Openreach FTTC via Plusnet - Unable to set up to reach...
smf22 wrote:I've not looked at the configuration of bridge-group etc., on EdgeRouter, [...]Maybe that's correct, but as I say, it looks inconsistent. RegardsYes, it is "correct" for bridging eth1 to...
View ArticleEdge OS loosing DHCP server configurations when uploading working config to...
I have a working config that I load and then modify based network specifics. However, when I have tried to load the config to new Edge OS versions, i.e. 1.5.xxx and up, I loose certain settings such as...
View ArticleRe: Max power output of ER-X-SFP for powering 4x UAP-AC-LR
You'll be fine. The ERX SFP can output POE on all five copper ports, and the power supply it comes with is big enough to do so.
View ArticleRe: Requests/suggestions for new hardware models
sorry, what do you mean by "proper" console port?
View ArticleRe: Requests/suggestions for new hardware models
As much as I whish for better OVPN speed, this is not gonna happen. OVPN has some problems with the implementation. It's not the encryption limiting it to a comparably low speed. So, offloading that...
View ArticleRe: Verifying QoS
for class 20 try dscp 26. And to elaborate to what said your download rules would have to be ip based as the dscp gets wiped out going over WAN.
View ArticleRe: IPV6-PD on Edgerouter X
So after setting that rule to rule 35 i finally get ipv6! ubnt@ubnt:~$ show ipv6 route IPv6 Routing Table Codes: K - kernel route, C - connected, S - static, R - RIP, O - OSPF, IA - OSPF inter area, E1...
View ArticleRe: Bridge VLAN IPTV
Solved with a lot of help from ubnt-member 'djnekkid' who has the same ISP as me.Thanks!
View ArticleRe: IPV6-PD on Edgerouter X
Good news. The firewall rule is a workaround though. You need to check with your ISP why there are two DHCP servers, one with no prefix to delegate.Regards
View ArticleRe: Load balance on two WANs doesn't quite work right
Thanks everyone for your suggestions. In the end, all that was required was allowing ICMP in the IPv4 network to make it all work. At some point, I'll remove it and check tcpdump logs to see what...
View ArticleEdgerouter won't play nice with BT IPTV
Just got my Edgerouter X today, everything seemed to be working fine until I wanted to watch an IPTV channel. From reading the forums it appears it's some kind of multicast issue?
View ArticleRe: Unable to log in to web GUI, SSH works fine
So yesterday out of nowhere my edgerouter lite stoped working and i cannot access it from gui, i did a hard reset but still nothing.I can access fine from ssh (putty). There are no gui services...
View ArticleRe: Routing between ETH1 and ETH2, while ETH2 uses DIFFERENT gateway
You probably need a WINS server. I try to stay away from Windows as much as possible so you will have to hope someone else here can elaborate or you need to do some google-fu.
View ArticleRe: EdgeMax POE with Openreach FTTC via Plusnet - Unable to set up to reach...
because on an ER-5, you have eth0, 1 -> routed only.eth2,3,4 -> part of switch0
View ArticleRe: EdgeMax POE with Openreach FTTC via Plusnet - Unable to set up to reach...
Thanks . As I said, nighttime reading for me.
View Article
More Pages to Explore .....