Re: Google Fiber - Which router should I buy?
kvic wrote:Thanks for letting us know. If your result is correct, I cannot figure what's going on inside then. We might have overestimated UBNT's due diligence and intelligence put into the ERX...
View ArticleRe: Default-action drop and logs - a little explanation please
Default action is a sort of invisible last rule at the bottom, blocking or allowing all traffic reaching there. Combining blocks and allows in a single ruleset is normal practice:example:allow...
View ArticleRe: Wierd issue with redundant EdgeRouter Lite
The ERs can't have identical configs, and be online at the same time. It'll result in IP conflicts
View ArticleRe: CLI commands for controlling OpenVPN client
https://community.ubnt.com/t5/EdgeMAX/EdgeOS-CLI-Primer-part-1/m-p/285388#U285388
View ArticleClik here to view.
Routing between ETH1 and ETH2, while ETH2 uses DIFFERENT gateway
ERLite-3Firmware v1.9.1 ETH0 -> WANETH1 -> 192.168.1.1 (DHCP .100 - .200)ETH2-> 192.168.2.1 (DHCP .100 - .200) When the DHCP from ETH1 uses 192.168.1.1 as gateway, and DHCP from ETH2 uses...
View ArticleRe: OpenNHRP Kernel Configuration
I just started emailing with Timo (creator of OpenNHRP) and he's been trying to get a patch pushed through for StrongSwan support. Here is his email to me: ---Most parts of the strongSwan integration...
View ArticleRe: OpenVPN - can't ping subnet at one ER-X 1.9.1
Yes, I will work on replicating this today. I will be in touch .
View ArticleRe: Routing between ETH1 and ETH2, while ETH2 uses DIFFERENT gateway
You need to set a manual route on clients that live on 192.168.2.0/24 that uses 192.168.2.1 as the gateway only for packets destined for 192.168.1.0/24.I don't know what kind of device 192.168.2.254...
View ArticleRe: Routing between ETH1 and ETH2, while ETH2 uses DIFFERENT gateway
Two possible solutions.On 192.168.2.254, set a static route for 192.168.1.0/24 to 192.168.2.1OrSet gateway on 192.168.2.1/24 to 192.168.2.1. Then on ER use Policy Based Routing source 192.168.2.0/24...
View ArticleRe: Unable to make IPv6 work on lan2
It would be helpful if others following this thread could weight in on how common is the case when ISP or network administrator in the enterprise give out /64 prefixes. In case they cannot be persuaded...
View ArticleRe: ER- 5 POE to ES 5 POE
Unfortuantely ER POE will not function well as a switch, only three of its ports are "Switched" and if you try to "bridge" in the other ports it will give you degraded performance. Definitely not...
View ArticleRe: Unable to make IPv6 work on lan2
The following script will achieve your Objective assumming that your ISP will dish out ... my ISP does:set interfaces ethernet eth0 dhcpv6-pd 'no-dns'set interfaces ethernet eth0 dhcpv6-pd pd 0...
View ArticleRe: Unable to make IPv6 work on lan2
. This will only work if you can request shorter than a /64 from the ISP on the WAN interface. For example: set interfaces ethernet eth0 dhcpv6-pd pd 0 prefix-length /56If you only get a single /64,...
View ArticleRe: Routing between ETH1 and ETH2, while ETH2 uses DIFFERENT gateway
gfunkdave wrote:You need to set a manual route on clients that live on 192.168.2.0/24 that uses 192.168.2.1 as the gateway only for packets destined for 192.168.1.0/24.I don't know what kind of device...
View ArticleRe: Unable to make IPv6 work on lan2
UBNT-sandisn wrote:It would be helpful if others following this thread could weight in on how common is the case when ISP or network administrator in the enterprise give out /64 prefixes. In case they...
View ArticleRe: Unable to make IPv6 work on lan2
smf22 wrote:@mozerd. This will only work if you can request shorter than a /64 from the ISP on the WAN interface. For example:Regards, I have been doing this with my ISP [Rogers] based on a /64 .... I...
View ArticleClik here to view.
Re: Small (and hopefully fast) question about edgeRouter pro
Hi, Sorry, I have some issues with translating technical terms, and some are completely new to me, . Your answer is perfect, though.I have looked up the sfp module and it is exactly what I was looking...
View ArticleClik here to view.
Re: Routing between ETH1 and ETH2, while ETH2 uses DIFFERENT gateway
I got a (stupid) followup question. PC's (Win10) on 192.168.2.x can access the NAS 192.168.1.55 - that works fine, so that required funcionality is there. but I suppose there is no way to get the NAS...
View Article
