ER firmware upgrade question
I have heard of upgrading the firmware on the ER would wipe off the existing configuration. Can someone please confirm that? Also, what's the best way to ensure that I have the most current...
View ArticleRe: BGP route-map
SPITwSPOTS wrote: ... The permit / deny logic between rules and how the le worked was really throwing me off. Just for my own understanding does that mean if you used "ge 8" and "prefix 10.0.0.0/32"...
View ArticleRe: IPV6-PD on Edgerouter X
stated for /56 prefix-id should be 01 - FF but that should actually be 00 - FF. And this shouldn't require the leading 0 should it?
View ArticleRe: IPV6-PD on Edgerouter X
The :: substitutes for leading zeroes if you put it in.Question: how does a link local WAN address work? Why would an ISP do that?
View ArticleVPN clients
Hi I have 2 EMAX 3-lite running 1.9.0. on different locations They are connected to each other with VPN ipsec and working very well with both 1.7.0 and 1.9.0 I also want to connect 3 separate PCs from...
View ArticleRe: IPV6-PD on Edgerouter X
okay so after playing around modifying host-address to :1 and adding prefix-id '::01' (not sure if this prefix id is correct) i get this cat /etc/radvd.confinterface switch0 { # This section was...
View ArticleRe: IPV6-PD on Edgerouter X
karog wrote:@smf22 stated for /56 prefix-id should be 01 - FF but that should actually be 00 - FF. And this shouldn't require the leading 0 should it?Correct. Just checking who's following along
View ArticleRe: Load balance on two WANs doesn't quite work right
Is that normal? Does have a different metric on each of the WAN routes cause this?
View ArticleRe: ER5 POE Google Fiber and Eth0 and 1
So instead of bridging, I could use Eth1 (Or eth0 as the config is set up) as for the Wifi UAP? If i want devices on Switch 0 and the say device on UAP to communicate (I.E. Wifi Roku stream from Wired...
View ArticleRe: Edgemax with Google Fiber and TV
jonboy345 wrote:Used the configs on my ERLite and was having some strange performance issues where the CPU was pegged at 100%.All of the applicaple HW offloading was enabled.I made a few tweaks to the...
View ArticleCenturyLink Fiber on ER-X
Hello, I'm having issues getting a full gigabit connection on ethernet. I'm getting ~200mbps down and up via ethernet and ~100mbps on Wifi using a Unifi-AP-LR. Could someone help me with my code?Also,...
View ArticleRe: Trouble getting PPPOE server to use DNS forwarding settings on Edgemax
Thank you for looking at the question >Is your guest network on eth1.101 which is using the gateway address as dns working okay? Yes From the original questionThis config using DHCP works;'Guest'...
View ArticleMyQ and ER-x
I'm new to Ubiquiti and have enough networking know how to get me in trouble so be patient. I have a MyQ Liftmaster internet gateway that connects to my garage door openers to the WAN. The device...
View ArticleEdge Pro - multiple wan ip not working
I'm trying to assign a block of /28 ip to a few clients. I followed tutorial from this link https://community.ubnt.com/t5/EdgeMAX/Multiple-IP-on-WAN-with-two-LAN-NAT/m-p/755942#M25566 when I issue...
View ArticleRe: Trouble getting PPPOE server to use DNS forwarding settings on Edgemax
Attached is the config file for the edgemax.It's basicly the same as above, I just rebuilt it from scratch again. In the config file:'Guest' VLAN 101 (172.16.0.0/24) DHCP server is set to use...
View ArticleRe: Mysterious router restarts
That error can be ignoredhttps://community.ubnt.com/t5/EdgeMAX/Explanation-of-log-entry/td-p/1058313It's kind of normal to see some errors in log, focus on errors on syslog host just before next crash
View ArticleRe: Load balance on two WANs doesn't quite work right
You're only looking at main routing table. Nothing wrong having only a single default there (cause =different metric). To tackle your problem: Make sure IPv6 works fine. Test on a client with IPv6...
View ArticleRe: Google Fiber - Which router should I buy?
I have tested a copper SFP with ERX SFP and the SFP is also limited to 1 Gbit aggregate.The part from the SDK said: "MT7621 default configuration setws GMAC1(RGMII1) connecting to GSW, and...
View ArticleRe: Load balance on two WANs doesn't quite work right
Thanks for the suggestion. I've already disabled IPv6 forwarding with set system ipv6 disable-forwardinguntil load-balancing becomes stable. Should I do more?
View ArticleRe: Multiple IP on WAN with two LAN - NAT
Hey - did you ever figure this out? I'm at the same spot you were. I have everything configured and the IP is working but everything is taking me back to the management screen. Thanks in advance!Matt
View Article
More Pages to Explore .....