Re: Edgerouter KPN IPv6
Hi and ,I'm not able to send pm's, so I hope you read this.. Are u both still using this setup? Am I right, that you don't have voip (vlan7) configured and that the rest of the ports are configured...
View ArticleEdgeMAX 1.9.1 port forwarding wizard not working for 80/443 ports
Port forwarding wizard doesn't work for me for forwarding ports 80 / 443 to some other server/port in local network. Forwarding from local network by using (Hairpin NAT) is working. But ports are not...
View ArticleRe: QoS ceiling
UBNT-Fenng wrote:@goldlineIT, the problem is solved. The reason is that the data traffic destination IP address must match the classifier of the QoS rule. @remikk, For example, maybe you can add the...
View ArticleRe: EdgeMAX 1.9.1 port forwarding wizard not working for 80/443 ports
Most residential ISP's block port 80,443,25
View ArticleRe: SNMP EdgeRouter Lite
Prtg does...all of thatIt samples packets sent on interfaces every 30 seconds, to show in its bandwidth charts
View ArticleRe: NAT Hairpin
Is it possible to use a comma separated list for destination port? For example: destination { address 192.168.1.0/24 port 80,443 }
View ArticleRe: Working with pseudo ethernet and 1to1 NATing to servers
Right now, I am working just a single public IP, but it looks like I can pull a few more with peth and that is what I'm looking to experiment with. When I put /24 in my examples, that is what my ERL...
View ArticleRe: Comcast IPv6 Settings Questions
I'm not sure what you mean by working fine. Having all the interfaces using the exact same address is not functional or proper. It would be the same as having all the interfaces as 192.168.1.1/24. You...
View ArticleRe: Comcast IPv6 Settings Questions
Thanks, . I'll keep Option 2. What I meant by "working fine" is that all clients seemed to be able to get their own IPv6 addresses and access the Internet via IPv6. But I see what you mean about it...
View ArticleRe: Comcast IPv6 Settings Questions
Option 2 is what is typically done.You could try option 1 with host-addresses 1, 2, and 3 respectively. You won't get host-address collisions on the LAN. SLAAC host-address are derived from MAC...
View ArticleRe: Comcast IPv6 Settings Questions
I would think the possibility exists with randomly generated privacy extension address's. Though it might be slim.
View ArticleRe: VTI performance not as expected
Isn't GRE offloaded? Have you considered using Ipsec with gre instead?
View Article1.9.1 no dns suffix workaround not working
I am experiencing the "no connection dns suffix" known issue in 1.9.1 and it's causing problems with dynamic dns updates on my lan. I've had the workaround in my config for sending dynamic updates to...
View ArticleRe: EdgeRouter restrict remote access to a particular MAC address
kuoh wrote: I haven't tried Open VPN with Ubiquiti yet, but it depends on how serious you need the security to be. We're not dealing with government or medical installations, so I just used the...
View Articleedgerouter x and vlans
Hello,have been using my edgerouter x without vlans but now I want to add a VLAN for my homeautmation. WHich runs separately and it should be totaly isolated from my default home network. I want to...
View ArticleRe: 1.9.1 no dns suffix workaround not working
I'm a fool. I was mixing up "option domain-name" and "option ddns-domainname". Setting the domain-name option correctly fixed it. Thanks for reading.
View ArticleRe: ER-X-SFP PoE input
Tested it on eth0 and eth1 and both accepted PoE input. Wouldn't assume PoE output would work without power adapter though, but this makes my installation tiny bit simpler still. Not sure about the...
View ArticleRe: edgerouter x and vlans
I think you are going in the right direction but I'd like to expand on it because I can't seem to figure out the sequence to enable VLANs successfully. I've got a mix of unifi and ER-X gear as shown...
View ArticleRe: Annoying issues with radvd
Do log files like /var/log/messages reveal anything about radvd exiting ?
View Article
More Pages to Explore .....