Re: EdgeRouter DNS server returning external IP instead of internal IP
cbfs wrote:I have an EdgeRouter set up with DHCP hostfile-update enable set, so there is an entry in the /etc/hosts file for the FQDN of one of my internal servers mapped to its internal IP address. I...
View ArticleRe: Two ER-X - One router one switch with VLANs
So I thought I had assigned VID's to eth1 on the first ER but either I never did or did something else incorrectly. I assigned 100,200 on eth1 on the first ER-X and it now works. My issue now is I...
View ArticleRe: What EdgeMax router to get for home based use
ER "Port Forward Wizard" - I'm not sure, TBH. Explicit DNAT rules - somewhere around 5,000 (rule numbers 5000+ are reserved for SNAT).
View ArticleRe: LAN specific client isolation (over wireless)?
So an update: It is positively the Echo. Found a great thread and apparantly it sends a UPnP/SSDP packet (part of the smart home devices discovery process) which resets airplay network controllers....
View ArticleRe: Two ER-X - One router one switch with VLANs
I meant, on the ER 1 something like While, on ER 2And, as said, the VIF5 on the switch0 ....Cheers,jonatha
View ArticleRe: Which Edge Router - 3 Different Applications
Assuming three physical ports are enough, an ERL could fit any of those scenarios. Heck, even an ER-X can easily handle a 50 mbit connection.
View ArticleRe: Edgemax with Google Fiber and TV
I was able to load the config to a backup on an ERL3 and receive the following error. ubnt@ubnt# load /config/user-data/config.boot Loading configuration from...
View ArticleRe: EdgeRouter X + UniFi AP = Mesh?
No, that's not what a "mesh" network is.You can, however, roam between the two APs
View ArticleRe: Disable iPv6 DNS servers
switch switch0 { address 192.168.0.1/23 bandwidth { } description Family firewall { in { modify PIA_ROUTE } } ipv6 { dup-addr-detect-transmits 1 router-advert { cur-hop-limit 64 link-mtu 0...
View ArticleProtocol types for ICMP v6
Hi, Edgemax has two of icmp v6 definitiols - 'ipv6-icmp' and 'icmpv6'. What's the difference? FYI, when using these for firewall rules, 'icmpv6' reports "invalid protocol icmpv6" when tring to save a...
View ArticleRe: Disable iPv6 DNS servers
To disable the DNS servers handed down by your ISP via DHCP, under your WAN interface: set interfaces ethernet eth0 dhcp-options name-server no-updateThis assumed eth0 is your WAN interface. This will...
View ArticleRe: Best way to learn Advanced QOS?
thx for good example, I put one config in test ER-X to play around, and try to understand how GUI works. Have to do my 1st QoS setup next week, but I'm tempted to use what I already did on other...
View ArticleRe: Edge max closes ports after I access them
Maybe the camera is playing tricks on you, not allowing multiple connections
View ArticleRe: Protocol types for ICMP v6
I think icmpv6 is just an alias for ipv6-icmp. I use icmpv6 (without error) in config but in ip6tables I see ipv6-icmp for the generated rules. Are you trying this within an ipv6-name ruleset as...
View ArticleRe: firewall user-defined chains
danielknowlab wrote:Hi thanks for coment, Well, I thought I was being explicit enough. Any way, for clareance:- Create "user-defined chain", the -N parameter of iptables- Use it as tarjet on a rule,...
View ArticleRe: Disable iPv6 DNS servers
I did forget to mention in my initial post, but I did do this. I am no longer receiving the iPv4 DNS servers via DHCP, I am however still receiving the iPv6 DNS servers. I did renew both the iPv4 and...
View ArticleRe: Frustrations with Offloading, ER-8 and gigabit fiber WAN
SOOOOOOOOO I was getting slow speeds straight from the fiber jack also. Turns out that most speed test sites are not setup for testing gig speeds. Google Fiber's speed test reports accurately (of...
View ArticleRe: Help with two separate WiFi networks behind EdgeRouter X
Starting to look at this again now. There are only two options on the Advanced Routing tab on the WRT-54G : Gateway and Router. And based on the onscreen help, Router is the option I want, as that is...
View ArticleRe: Help with two separate WiFi networks behind EdgeRouter X
You should not be setting any static routes. The WRT is being used as a switch only, no router functionality hence who you are not suppose to be using the WAN interface on the WRT or the R7000
View Article