Re: EdgeRouter-X: Hardware Offload
cbfs wrote:... Is there any use case where you would want hardware offloading disabled? As per 1.9.1 release notes (here): Known issues [IPSec] IPSec ofload on ER-X/ER-X-SFP/EP-R6 platforms is causing...
View ArticleRe: EdgeOS CLI Primer (part 1)
, start a new thread. This thread is about the CLI Primer.
View ArticleRe: Log file management
Thanks for the quick reply. I do actually have a remote syslog server running on another machine and do have the ERL sending to it, however, I was under the impression that even if you send stuff to...
View ArticleDHCP Static mapped IP never offered
I suspect I am doing something incorrectly. I want my customers to use DHCP on their routers so I can reconfigure my network at some later date if needed. But, I want to statically map their IP's for...
View ArticleRe: DHCP leases aren't shown for vlan eth1
If you are running from run and not configure mode, that would mean you are not using the dnsmasq dhcp server.Please post your sanitized configuration.
View ArticleRe: PPPoE broken in 1.9.1?
lancer73 wrote: ...pppoe did come up, but with no IPv6. When I tried to restart radvd it told me that radvd.conf was empty...Similar issue was already discused...
View ArticleRe: Log file management
/var/log is non-persistent; not written to flash. Files are rotated fairly quickly to manage space.
View ArticleRe: Newbie needs help setting up EdgeRouter 8
Thanks dpurgert. I have a cable modem in the basement, a wireless router on the first floor, and a wireless router on the second floor. I have 2 wired pcs on the first floor. Would you connect the...
View ArticleRe: Newbie needs help setting up EdgeRouter 8
Modem -> Router (ER-X / ER-X-SFP are my goto for small setups) -> Switch -> all other devices. While you're at it, would probably be a good idea to trash the other routers and replace with...
View ArticleRe: Black hole route vs firewall rule to drop packets
Black hole routing will possibly have a lower CPU/processing overhead on the router than a firewall. The firewall though allows you to be more granular with what you drop. At the network edge you have...
View ArticleRe: OSPF and PPPoE server
Can you use a pool for pppoe addresses, add a black-hole route to this entire pool, and redistribute this static null route?
View ArticleRe: Log file management
chaycock wrote:How does the system manage the logs in /var/logs to keep them from filling up all of the disk space?For example, I turned on dns logging, so the dnsmasq.log gets a lot of activity. What...
View ArticleRe: Black hole route vs firewall rule to drop packets
a firewall rule uses ipset lists, this is a fast mechanism to match traffic for a huge address/network group.(like country , or spam blacklists)I'm not sure route table will be as fast with all...
View ArticleRe: Dual WAN - L2TP VPN Connection problem
Thank you for your suggestions. I'll give it a try. Maybe it will take some time. I#m afraid of doing this changes remote ;-).
View ArticleRe: OpenVPN - can't ping subnet at one ER-X 1.9.1
Also just removed the IPSEC tunnel from both sides and same results. I see the traffic going to 10.249.16.0/23 (site b) flowing through vtun0 but no reply but when I do a tcpdump -i vtun0 on Site B, I...
View ArticleRe: OpenVPN - can't ping subnet at one ER-X 1.9.1
Why you use maks /23? If the VPN IP can be ping. Then the problem may be the interface IP setting or routes setting.
View ArticleRe: OpenVPN - can't ping subnet at one ER-X 1.9.1
/var/log/messagesSite A:# more /var/log/messages | tail -f Jan 9 09:47:54 rt111P openvpn[20338]: 98.124.5.101:32889 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 2048 bit RSA Jan 9...
View ArticleRe: OpenVPN - can't ping subnet at one ER-X 1.9.1
NO. I think this maybe not OPEN VPN issue.It is the network IP/mask, or routes issue. In both sides, what is the output of "ip route get x.x.x.x " x.x.x.x is the ip of the other site.
View ArticleRe: OSPF and PPPoE server
Hack? Workaround?imho, good practice! You want to keep your routing protocol quiet, not having to recalculate routes when any customer restart their equipment.
View Article
