Re: A simple question
Thanks so much for this guidance I had no trouble adding the '3' network but I'll have to wait until I return to VT to implement the host part.This needs to be rolled into the setup for AirMax devices...
View ArticleRe: A simple question
You can setup your firewall rules on eth4 for security. Blocking anything coming in but allowing LAN access out so you can still connect to the radios.
View ArticleRe: A simple question
Now this is an excellent point. The concern that drives me is that I can 'bypass' the ERX by cabling from modem to bridge to unmanaged switch to eth0 and from switch to eth4 and access my devices...
View ArticleNo internet with new modem
I upgraded my service and had to install a new cable modem. I can access the internet by connecting a laptop directly to the Ethernet port on the modem so I know that I do have service. When I connect...
View ArticleRe: A simple question
You can also take it 1 step further and also block all LAN access to eth4 but only allow your PC's IP out.
View ArticleRe: when to use destination port vs source port?
have you assigned the firewall rules to your interfaces? Something like below. ethernet eth1 { address dhcp description WAN1 duplex auto firewall { in { name WAN_IN } local { name WAN_LOCAL } } speed...
View ArticleRe: ERX Wifi vlan routed to VPN connection
Redfive, I assume in this case I would need basicly be doing the following below. set interfaces switch switch0 vif 94 firewall in modify express_vpn_routethe firewall in rule for express_vpn_route is...
View ArticleRe: No internet with new modem
You need power cycle your modem after it has been connected to your ERX.
View ArticleEdgeRouter Lite 3-port - multiple power supplies "on the blink".
For my clients I usually deploy EdgeRouter Lite 3 port routers. Sadly, over time I have had to replace all of them due to bad memory modules or some just brick (including the one I use for my home)....
View ArticleRe: No internet with new modem
That fixed it. Thank you. I thought I had already tried that but apparently I had not. I was powering on the modem before powering the router up.
View Article1 of 9 site's can't connect to my locally hosted unifi controller behind ER-8
I know this is the Edgemax section, please read on to understand why I'm posting here. So I host a Unifi controller for 9 sites at my home. 1 of those 9 recently started showing all devices were...
View ArticleRe: Edge Router - Eth0 Disappeared
Hi Getting error Can not assign network address as IP address
View ArticleRe: L2TP Vpn Routing All Traffic?
Just wanted to add that on Windows 10, I was able to create a split tunnel by setting up the VPN: Add-VpnConnection -Name "YourVpnName" -ServerAddress example.com -TunnelType L2tp -EncryptionLevel...
View ArticleRe: Edge Router - Eth0 Disappeared
Ok, fixed it. It seems the ISP didn't give the Usable IP address directly but gave the network address. Had to calculate the usable host and use one of the IPs as WAN iP
View ArticleAdvertising full routing table to peer
I have an iBGP session setup between a UBNT and a Mikrotik. The UBNT is bringing in a couple of full routing tables. I want to pass these along to my ibgp peer. So far I have not been able to do...
View ArticleRe: when to use destination port vs source port?
is creating zone based firewall, so you don't assign firewall rules to an interface.Normally , you allow traffic from zone1 -> zone2, and return traffic is automatically allowed (with...
View ArticleRe: ERX Wifi vlan routed to VPN connection
Double check the VIF's and ip addresses.Cheers,jonatha
View ArticleRe: when to use destination port vs source port?
Ah thanks. I mislead myself by not seeing the firewall rule applied anywhere. Guessing these are applied in the zone policy that was not shown then.
View ArticleRe: EdgeRouter X SFP and EdgeSwitch ES‑8XP, can't get an IP for my switch and...
Hi, All my devices get an IP and they can comunicate together, but I can't get access to internet from my devices. What am I missing. My ISP is eth0 and my router is eth1. firewall {all-ping...
View Article