Re: firewall question
You're allowing everything through, seems likely you're not blocking anything. 's suggestions with checking log for passed traffic, and packet capture, is best next step. Traffic outbound from that...
View ArticleRe: erx unable to sync with any ntp server
$ show ntp 0.asia.pool.ntp.org server 62.201.225.9, stratum 2, offset 0.092916, delay 0.24135 server 118.67.200.10, stratum 2, offset 0.099922, delay 0.12849 server 210.23.25.77, stratum 1, offset...
View ArticleRe: Experiencing packet loss to Googles DNS servers
Seems to me like google 8.8.8.8 doesn't throttle ping requests:On Cisco testrouter, pinging 1000 times goes flawless and takes total 20 seconds ( 50 pings per second)Cisco#ping 8.8.8.8 repeat 1000 Type...
View ArticleClik here to view.
Re: OpenVPN site-to-site tunnel - ERLite to ERLite - best vpn throughput...
3rdcoastnet wrote:There are a million ways to skin a cat, and tons of more secure strategies[..]I know personally I was being attacked CONSTANTLY on port 22 on a public DMZ server. Simply changing the...
View ArticleRe: ERX IPSec disconnecting approx. every 2 minutes
Hi, I collected the output from the swanctl --log. I see there two disconnect and two connect, but nothing special. You can take a look at the log file.
View ArticleClik here to view.
Re: Source Based Routing Problem
Pull out two of the three 0.0.0.0/0 routes in the main table (you only ever want one). The right setup is one of the WANs uses the main table (e.g. WAN1) and the other two get custom tables. ugh, too...
View ArticleClik here to view.
Re: Experiencing packet loss to Googles DNS servers
That may be your experience.... mine is different. The following is a graph from smokeping to Google and as seen, there is loss during peak times. This pattern was repeated consistently day after day....
View ArticleRe: Sticky Connections Not Running
Hello, Please, I need a support.Ancheng, Stig, Mlin, Somebody??? Is it true that Stig does not work in this company anymore? Best Regards,
View ArticleRe: VoIP QoS - Limit Bandwich peer IP
Hello, Please, I need a support.Ancheng, Stig, Mlin, Somebody??? Best Regards,
View ArticleRe: ERX IPSec disconnecting approx. every 2 minutes
mgi wrote:Hi, I collected the output from the swanctl --log. I see there two disconnect and two connect, but nothing special. You can take a look at the log file.Well, actually there's lots of special...
View ArticleRe: Load balance & site authentication issues
Hello, BranoB, I agree with JVComputers.This KB does not work properly.JVComputers, this was also my only alternative.See my post, where I also ask for help...
View ArticleDirecting Destination of Traffic
Hi, Any solution available for directing traffic through either WAN 1 or 2 based on destination IP? Example: Traffic for directory.website.com (or IP equivilent) is sent through WAN 1. Thanks in advance.
View ArticleRe: Directing Destination of Traffic
I may have solved it. Does the 'Sticky' function do what I am after?
View ArticleRe: radvd dies when pppoe drops
Thanks, I opened a bug ticket. I have a few other things I need to complete first, but if no one beats me to it I'll look at it.
View ArticleCan ERLite-3 config be restored on ERPoe-5
I am thinking of replacing my existing ERLite-3 with ERPoe-5. Can I restore the ERLite-3 config onto ERPoe-5? Presently on ERLite-3, I have eth0 - WAN, eth1 - standby WAN, eth2 - LAN. Assuming...
View ArticleClik here to view.
To enter on account not ip doubt
Good morning as you know in the post of loadbalancing at the end I managed to balance the 2 lines adsl pppoe, my question is:When I try to enter my server from an outside connection to my network with...
View ArticleRe: Directing Destination of Traffic
Well, basic routing is always destination based. Usually a routing table is pretty simple. One route for the connected subnet - this routes all internal traffic through the interface directly into the...
View ArticleRe: erx unable to sync with any ntp server
ntp status output looks fine. You even got connected to a stratum1 server!Does output of "date" command show correct time?
View ArticleRe: Directing Destination of Traffic
hsimah wrote: Does the 'Sticky' function do what I am after?No, you need PBR - Policy Based Routing ... you may need to modify your criteria for source/destination address or destination port.
View ArticleRe: Can ERLite-3 config be restored on ERPoe-5
Yes, you can do that. If you've not purchased ER-PoE consider ER-X or ER-X-SFP (has PoE on all interfaces). Both have HW switch.
View Article